Bedienungsanleitung Solo 652 (Seite 18 von 26) (Englisch)

658828

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Operating and maintenance information

ENGLISH 18 - 40 -.

11.2 Maintenance and care of the cutting gear

Saw chain:

Just like any other cutting tool, the saw chain is

subject to natural wear. Your chainsaw will only be

able to deliver its full potential if the saw chain is

correctly sharpened. Every saw chain is matched to

the relevant chainsaw type in terms of its form,

cutting performance and design. Only use the

genuine SOLO saw chain which is approved for your

chainsaw / guide bar type.

Permissible cutting gear and the corresponding

cutting lengths Î refer to the last two inside pages of

this operating manual ( - 258 -.)

Sharpening the saw chain:

A special round chain file with the correct diameter

should be used for sharpening. Normal round files

are not suitable.

A file holder makes

guidance of the file

easier, as it has

markings for the

correct sharpening

angle (align the

markings parallel to the

saw chain) and limits

the penetration depth

(4/5 of the file

diameter)

Position the file holder on the roof of the tooth. The

file should only engage during the forward stroke. Lift

the file off when moving it back.

The shortest cutting tooth is

sharpened first. The length of

this tooth is then the target

size for all the other teeth on

the saw chain. All of the cutting elements must have

the same length.

To start with, file all of the cutting elements on one

side from the inside outwards, then file all of the

cutting elements on the other side.

Always fully file out any damage from the side plate

or the roof of the tooth.

Correction of the depth limiter:

The distance b between the

depth limiter (round nose) and

the cutting edge defines the

thickness of the chips. The

best cutting results are

obtained with the prescribed

depth limiter spacing, which

should be checked every time

the saw chain is sharpened.

Lay the depth limiter gauge on

the cutting element. If the

depth limiter protrudes, file off

the protruding part with a flat

file.

Round off the front edge of

the depth limiter. The original

shape must be restored.

CAUTION: If the spacing is too large then there

is a greater risk of kickback.

For your safety: If you would like to pull the chain

through while filing, pull the chain forwards with a

screwdriver towards the tip of the rail. This will reduce

the risk of slipping.

Sprocket

Before you can fit a new saw chain you must check

the condition of the sprocket. Worn sprockets will

damage your new saw chain. If necessary, replace

the sprocket with the new chain. Grease the bearing

with lithium-based grease whenever the sprocket is

replaced.

Tip: We recommend the use of two saw chains per

sprocket, and that both chains should be replaced as

frequently as possible so that all of the components

wear evenly. Once a certain wear limit is reached,

replace all of the parts together again.

To replace the chain

wheel (after dismantling

the guide bar cover and

the guide bar with chain),

push the chain wheel with

its washer down slightly

and lift off the locking ring

with a small screwdriver.

To refit the locking ring after

fitting the new chain wheel

push the chain wheel, with

its washer, down again

slightly. It is best to use flat

pliers when refitting the

retaining ring.

Files Ø mm/inches 4.8 /

Filing angle α ° 30°

Depth limiter spacing b mm/inches 0.64 / .025’’

Filing direction

10°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 652 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo 652

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info