Bedienungsanleitung Solo 652 (Seite 19 von 26) (Englisch)

658828

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Operating and maintenance information

- 41 - ENGLISH 19

Guide bar:

The guide bar of your

chainsaw requires just as

much care as the saw

chain. The running

surfaces must be flat and

level, and the groove must

not be widened.

In order to prevent one-sided wearing of the guide

bar, we recommend that the guide bar be reversed

whenever the chain is sharpened.

On guide bars with a guide

sprocket, the bearing of the

guide sprocket should

preferably be lubricated with

ball bearing grease (through

the lubricating hole on the side with a grease gun)

every time the chainsaw is refuelled. Rotate the

guide sprocket while doing this.

Important: The guide bars are only designed to

guide the saw chain and must not be used as a

levering tool. Any twisting or turning or use of the

guide bar to gain leverage in the wood shortens the

service life of the guide bars.

11.3 Air Filter Maintenance

Contaminated air filters cause a reduction in engine

performance and increase fuel consumption with

more pollutants in the exhaust gas. Engines are less

likely to start readily with a contaminated air filter.

When using the power tool all day, clean the air filter

daily; under very dusty conditions, even several

times a day.

Carry out the following maintenance jobs regularly.

Taking off the cowl:

• Release the three fastening

clips (16), preferably by

applying a screwdriver in a

twisting motion.

• Lift off the cowl (5) upwards.

Cleaning the air filter

• Important: Pull out the choke (7).

• Push both clamping brackets (a) with a screwdriver

off the filter casing.

• Remove the upper filter part (b).

• Simply tapping or careful blowing through the filter

is the best method for cleaning. When using

compressed air, wear eye protection (e.g. safety

goggles), and hold the compressed air stream not

too closely against the air filter.

• In case of severe contamination, the air filter can

be cleaned with non-flammable cleaning fluid

(warm soapy solution).

NB: The air filter must be absolutely dry before

it is reinstalled.

• Clean the lower casing part (c) up to the closed

choke damper with a paint brush or remove dirt

and dust particles carefully by blowing them out of

the casing.

• After cleaning, carefully position the dry filter

element (b) onto the lower casing part (c). There

must not be any open gap around the filter

element.

• Close the air filter securely with both clamping

brackets (a).

The corresponding parts should be replaced

immediately if the filter material is damaged. No

warranty claims can be accepted for engine damage

arising as a result of inadequate care.

Fitting the cowl

For ease of installation press the hand

protection (3) forwards (chain brake is

applied).

• Fit the cowl, making sure it goes on straight.

• Insert the cowl in the slot on the main housing,

making sure that it fits properly in the slot all the

way around.

Once the cowl is correctly seated, secure the cowl

again using the three fastening clips (16).

Fig. 16

Fig. 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 652 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo 652

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info