Bedienungsanleitung Sommer S 9080 pro (Seite 58 von 88) (Englisch)

680782

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

S10931-00001_Rev-D_EN

11. Connections and special functions of the wall

control unit

Installing the keypad

1. When installing the potential-free keypad, select

a suitable position at a height of at least 1.6 m.

2. Install the keypad.

3. Route the keypad cable to the wall control unit and

secure it firmly to prevent displacement.

Installing the control cable and settings on the

wall control unit

1. Disconnect the operator from the mains voltage.

Check it is disconnected from the power supply.

2. Unscrew the light cover from the wall control unit

and remove it upwards. Hold the front cover firmly

while doing so.

3. Remove the control unit cover gently towards

the front and unplug the connection cable for

the membrane keypad from the wall control unit,

see chapter "7.3 Light and control unit cover of

the wall control unit."

4. If an accumulator is used, it must also be

disconnected, see Chapter "11.12 Installing and

removing the accumulator."

5. Remove the control unit cover.

24V/1A

Signal

COM

GND

+24V

+24

1234

Fig. 6 Fig. 7

6. Connect the cable of button 2 to the terminal block

for COM and Signal.

⇒ Button 2 is connected.

7. Set DIP switch 4 on the wall unit to "ON."

8. Plug in the connection cable for the button and

for the accumulator, if necessary.

9. Close the ceiling control unit in reverse order,

see chapter "11.12 Installing and removing the

accumulator" and "7.3 Light and control unit

cover of the wall control unit."

10. Supply the operator with the mains voltage.

Check that the power supply is connected.

Settings on the motor carriage

To determine the partial opening door position, the

following settings must be made on the motor carriage.

1. Close the door completely up to the door CLOSE

end position.

2. Open the motor carriage, see chapter "7.1 Cover of

the motor carriage."

3. Set DIP switch 2 on the motor carriage to "ON."

4. Press button 2 for the partial opening function.

⇒ The door moves in door OPEN direction.

5. Press button 2 again for the desired position for

stopping.

⇒ The door stops at the desired position.

11.6 Deleting partial opening

1. Set DIP switch 2 on the motor carriage to "OFF."

2. Open the door completely up to the door OPEN

end position.

⇒ Partial opening is deleted.

To program a new position, see chapter "10.17 Setting

partial opening."

11.7 Photocell and frame photocell

A 2-wire photocell from SOMMER or a 4-wire photocell

can be connected to the control unit. The control unit

automatically detects which version it is and sets itself

to that version.

Fig. Terminal for a 2-wire photocell

24V/1A

Signal

COM

GND

+24V

Fig. Terminal for a 4-wire photocell

INFORMATION

If a photocell is retrotted on

a programmed system, the control

unit must be reset, see chapter

"10.13 Performing a reset."

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sommer S 9080 pro Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sommer S 9080 pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info