Bedienungsanleitung Sony BDV-N990W (Seite 56 von 68) (Englisch)

533600

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Severe hum or noise is heard.

t Move your TV away from the audio

components.

t Clean the disc.

The sound loses stereo effect when you play

a CD.

t Select stereo sound by pressing AUDIO

(page 35).

The sound comes from the center speaker

only.

t Depending on the disc, the sound may come

from the center speaker only.

No sound or only a very low-level sound is

heard from the surround speakers.

t Check the speaker connections and settings

(pages 17, 39).

t Check the sound mode setting (page 26).

t Depending on the source, the effect of the

surround speakers may be less noticeable.

t A 2-channel source is being played.

Distortion occurs in the sound of a connected

component.

t Reduce the input level for the connected

component by setting [Attenuate - AUDIO]

(page 47).

Wireless transmission is not activated or

there is no sound from the surround

speakers.

t Check the status of the LINK/STANDBY

indicator on the surround amplifier.

• Turns off.

– Check that the AC power cord (mains

lead) of the surround amplifier is

connected securely.

– Turn the surround amplifier on by

pressing "/1 on the surround amplifier.

• Flashes green quickly.

– 1 Press "/1 on the surround amplifier.

2 Insert the wireless transceiver into the

surround amplifier correctly.

3 Press "/1 on the surround amplifier.

•Flashes red.

– Press "/1 to turn off the surround

amplifier, and check the following items.

1 Are the + and – speaker cords short-

circuited?

2 Is anything blocking the ventilation

holes of the surround amplifier?

After checking the above items and fixing

any problems, turn on the surround

amplifier. If the cause of the problem

cannot be found even after checking all the

above items, consult your nearest Sony

dealer.

• Flashes green or orange slowly or turns red.

– Make sure that the wireless transceiver is

inserted correctly into the main unit.

– Make the [Secure Link] setting again

(page 43).

– Sound transmission is poor. Move the

surround amplifier so that the LINK/

STANDBY indicator turns green or

orange.

– Move the system away from other

wireless devices.

– Avoid using any other wireless devices.

• Turns green or orange.

– Check the speaker connections and

settings.

Noise is heard from surround speakers or

sound from the surround speakers skips.

t Wireless transmission is unstable. Change the

[RF Channel] setting in [Wireless Sound

Connection] (page 44).

t Install the unit and surround amplifier closer to

each other.

t Do not install the unit and surround amplifier

in a closed rack, on a metal rack, or under a

table.

Radio stations cannot be tuned in.

t Check that the antenna (aerial) is connected

securely. Adjust the antenna (aerial) or connect

an external antenna (aerial) if necessary.

t The signal strength of the stations is too weak

(when tuning in with automatic tuning). Use

manual tuning.

Wireless sound

Tuner

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony BDV-N990W Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony BDV-N990W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info