Bedienungsanleitung Sony CDP-XE200 (Seite 12 von 46) (Englisch, Französisch, Spanisch)

50589

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

Recording From CDs

To check and change your program

See page 11.

The indication appears while checking the program

for side A and while checking the program for side

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

Recording a CD by Specifying

Tape Length (Time Edit)

(CDP-XE500 only)

You can have the player create a program that will fit

the length of the tape.

The player automatically creates a program, keeping

the original order of the disc.

The program can contain up to 24 tracks (a pause

inserted between tracks is counted as one track).

Note that tracks whose numbers are over 24 cannot be

programmed automatically.

EDIT/TIME FADE

0 / )

4 When you record on both sides of the tape, press

EDIT/TIME FADE again.

The player inserts a pause, then creates the

program for side B. The display shows the

programmed tracks.

When you record on one side of the tape or on a

DAT or MD, skip this step.

5 Start recording on the deck and then press · on

the player.

When you record on both sides of the tape, the

player pauses at the end of the program for side A.

6 When you record on side B, reverse the tape and

press · or P on the player to resume playing.

To cancel Time Edit

Press PLAYMODE until “SHUFFLE” and “PROGRAM”

disappear from the display.

When using the remote, press CONTINUE.

You can program the tracks you want in advance

Select the tracks before doing the above procedure. The

player creates a program from the remaining tracks. In

this case, you cannot select “HALF” to specify the tape

length.

You can freely specify the tape length

Set the tape length using ≠ AMS ±.

Example: When the tape length of one side is 30 minutes

and 15 seconds

1 To set the minutes, turn ≠ AMS ± until

“30” appears in the display, then press

ENTER .

2 To set the seconds, turn ≠ AMS ± until

“15” appears in the display, then press

ENTER .

When tracks, which aren’t numerically consecutive on

the disc, are programmed consecutively (i.e. 1, 3, 5

etc.)

A one-second access time blank is added between the

tracks.

To check and change your program

See page 11.

1 Press EDIT/TIME FADE before you start playing

until EDIT appears and “A” in the indication

flashes in the display.

2 Press 0 or ) to specify the tape length.

Each time you press these buttons, the display

changes as shown below, with the tape length of

one side following each indication.

n HALF ˜ C-46 ˜ C-54 ˜ C-60 ˜ C-74 ˜ C-90 ˜ - - .- - N

(23.00) (27.00) (30.00) (37.00) (45.00)

When you select “HALF”

The player sets the program of each side to a half of the

total playing time of the disc. Note that you cannot select

“HALF” when the disc has more than 24 tracks.

3 Press EDIT/TIME FADE to have the player create

the program.

The display shows the tracks to be recorded. “B” in

the indication flashes in the display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony CDP-XE200 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony CDP-XE200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info