136405
19
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
Chapter 1 Overview 19
Chapter 1 Overview
5 COMPONENT OUT jacks
Use to output component signals.
To connect a device equipped the component video
input connector, use COMPONENT OUT jacks on the
unit. If you use COMPONENT OUT jacks, you can
output high-quality video with less signal deterioration
in quality than S VIDEO jack.
You can set the output video format by using [HDMI/
CMPNT] of [VIDEO OUT] in [IN/OUT REC] menu.
When DISPLAY OUTPUT switch is set to ALL, text
data such as time code, menu, and alarm message are
superimposed on a monitor connected using
COMPONENT OUT jacks (page 25).
Notes
•When images are output in 720p format, some of the
text image data (outer frame: underscan portion) on
the monitor may appear cut out. In this case, check
the text image data on LCD monitor of the unit or on
a monitor using S VIDEO OUT jack or the VIDEO
OUT jack. Also, when your monitor has an underscan
function, you can check all the text data on the
monitor during underscan.
•When you change the video format setting of [HDMI/
CMPNT] of [VIDEO OUT] in [IN/OUT REC] menu,
the video signal output from S VIDEO jack, VIDEO
jack, or
HDV/DV jack may be distorted for a
moment.
•When you play back an HDV-formatted tape with
copyright protected signals or input HDV signals
with copyright protection to
HDV/DV jack, pictures
may be output in either 480i (NTSC) or 576i (PAL)
format, regardless of the setting of [HDMI/CMPNT]
of [VIDEO OUT] in [IN/OUT REC] menu.
•When you play back a tape in DVCAM/DV format
and while an EE picture in NTSC/PAL is displayed,
the 480i resolution or the 576i resolution is output,
regardless of the setting of [HDMI/CMPNT] of
[VIDEO OUT] in [IN/OUT REC] menu.
The output level of COMPONENT OUT jacks is as
follows:
Output at 480i NTSC
With [BETACAM] selected in [IN/OUT REC] menu
Y: 1.0 Vp-p
(with 0.286 Vp-p sync negative,
output impedance 75 (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 (ohms), unbalanced)
(75% color bars with 7.5 IRE setup)
With [SMPTE] selected in [IN/OUT REC] menu
Y: 1.0 Vp-p
(with 0.3 Vp-p sync negative,
output impedance 75 (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 (ohms), unbalanced)
(100% color bars with no setup)
Output with other settings
Y: 1.0 Vp-p
(output impedance 75 (ohms), unbalanced)
Pb/Cb/B-Y, Pr/Cr/R-Y: 0.7 Vp-p
(output impedance 75 (ohms), unbalanced)
(100% color bars with no setup)
480i/480p:
Y: with 0.3 Vp-p sync negative
1080i/720p:
Y/Pb/Pr: with 0.6 Vp-p 3-level sync
(Continued)
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sony hvr m25p wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info