Bedienungsanleitung Sony MDS-S37 (Seite 10 von 36) (Holländisch)

40280

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Recording on MDs

Monitoring the input signal (Input Monitor)

Before starting recording, you can monitor the selected

input signal through the deck’s output connectors.

1 Press § to remove the MD.

2 Set INPUT according to the input signal you want

to monitor.

When INPUT is at ANALOG

The analog signal input through LINE (ANALOG) IN is

output to DIGITAL OUT after A/D conversion, and

then to the LINE (ANALOG) OUT connectors and

HEADPHONES jack after D/A conversion.

When INPUT is at DIGITAL

The digital signal input through DIGITAL IN is output

to DIGITAL OUT, and then to the LINE (ANALOG)

OUT connectors and HEADPHONES jack after D/A

conversion.

Note

Even if you set REC MODE to MONO, the monitor

signal does not become monaural.

3 Press r.

If INPUT is at ANALOG, “AD-DA” appears in the

display.

If INPUT is at DIGITAL, “-DA”appears in the

display.

If “Auto Cut” appears in the display

(Auto Cut)

There has been no sound input for 30 seconds while

INPUT is set to DIGITAL and the source is connected

through DIGITAL IN. The 30 seconds of silence are

replaced by a blank of about 3 seconds and the deck

changes to recording pause.

You can turn off the Auto Cut Function

For details, see “If “Smart Space” appears in the

display” below.

If “Smart Space” appears in the display

(Smart Space)

There has been an extended silence of 4 to 30 seconds

in length when INPUT is set to DIGITAL and the

source is connected through DIGITAL IN. The silence

is replaced with a blank of about 3 seconds and the

deck continues recording.

To turn off the Smart Space Function and Auto Cut

Function

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES.

3 Press EDIT/NO to display “S. Space OFF.”

To turn on the Smart Space Function and Auto Cut

Function again

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES twice to display “S. Space ON”.

Notes

• When you turn off the Smart Space Function, the Auto Cut

Function is also turned off automatically.

• The Smart Space Function and Auto Cut Function are

factory set to on.

• The Smart Space Function does not affect the order of the

track numbers being recorded, even if the blank space

occurs in the middle of a track.

• If you turn off the deck or disconnect the AC power cord,

the deck will recall the last setting (on or off) of the Smart

Space and Auto Cut Functions the next time you turn on

the deck.

Playing back tracks just recorded

Do this procedure to immediately play back tracks that

have just been recorded.

Press ﬂ (or ·) immediately after stopping

recording.

Playback starts from the first track of the material just

recorded.

To play from the first track of the MD after recording

1 Press p again after stopping recording.

2 Press ﬂ (or ·).

Playback starts from the first track of the MD.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony MDS-S37 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info