Bedienungsanleitung Sony MDS-S37 (Seite 12 von 36) (Holländisch)

40280

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Recording on MDs

Marking Track Numbers While

Recording (Track Marking)

You can mark track numbers either manually or

automatically. By marking track numbers at specific

points, you can quickly locate the points later using the

AMS Function or Editing Functions.

To cancel Automatic Track Marking

1 Press EDIT/NO during recording or recording pause.

“LevelSync ?” appears in the display.

2 Press YES.

3 Press EDIT/NO.

“LevelSyncOFF” appears in the display.

* The signal level must remain low for 2 or more seconds

before a new track number is marked.

When you want to mark track numbers after you‘ve

finished recording

Use the Divide Function (see “Dividing Recorded

Tracks” on page 22).

Note

If you turn off the deck or disconnect the AC power cord, the

deck will recall the last setting (LevelSync on or off) of the

Automatic Track Marking Function the next time you turn

on the deck.

Starting Recording With

2 Seconds of Prestored Audio

Data (Time Machine Recording)

When recording from an FM or satellite broadcast, the

first few seconds of material are often lost due to the

time it takes you to ascertain the contents and press the

record button. To prevent the loss of this material, the

Time Machine Recording Function constantly stores 2

seconds of the most recent audio data in a buffer

memory so that when you begin recording the

program source, the recording actually begins with the

2 seconds of audio data stored in the buffer memory in

advance, as shown in the illustration below:

Marking track numbers manually

(Manual Track Marking)

You can mark track numbers at any time while

recording on an MD.

Press r at the place you want to add a track mark

while recording.

Marking track numbers automatically

(Automatic Track Marking)

The deck adds track marks differently in the following

cases:

• When recording from CDs or MDs with INPUT at

DIGITAL and the source connected through

DIGITAL IN:

The deck marks track numbers automatically. When

you record from a CD or MD, the track numbers are

marked as they are found on the original.

• When recording with INPUT at ANALOG and the

source connected through LINE (ANALOG) IN, or

when recording from DAT or satellite broadcasts

with INPUT at DIGITAL and the DAT or satellite

broadcasts connected through DIGITAL IN:

The deck marks a new track number whenever the

signal level drops and rises to a certain point*

(Automatic Track Marking). If “LEVEL-SYNC” does

not light up, set the LevelSync to ON as follows:

1 Press EDIT/NO to display “LevelSync ?”during

recording or recording pause.

2 Press YES twice to display “LevelSync ON.”

“LEVEL-SYNC” appears in the display.

End of the program

source to be recorded

Time

Recorded

portion

When you press

AMS in Step 3

Beginning of the program

source to be recorded

EDIT/NO YESr

•

·∏

)

Audio data in 2-second buffer memory

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony MDS-S37 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info