Bedienungsanleitung Sony RHT-G500 (Seite 33 von 40) (Englisch)

61906

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Additional Information

If you experience any of the following

difficulties while using the system, use this

troubleshooting guide to help remedy the

problem before requesting repairs. Should any

problem persist, consult your nearest Sony

dealer. When bringing the system in for repairs,

be sure to bring in the entire system.

General

The power is not turned on.

• Check that the AC power cord (mains lead)

is connected securely.

If “PROTECTOR” and “PUSH POWER”

appears alternately in the front panel display.

Press ?/1 to turn off the system, and check

the following item after “STANDBY”

disappears.

• Is anything blocking the ventilation holes of

the system?

After checking the above item and fixing

any problems, turn on the system. If the

cause of the problem cannot be found even

after checking the above item, consult your

nearest Sony dealer.

Dolby Digital or DTS multi channel sound is

not reproduced.

• Make sure that Dolby Digital or DTS sound

format is selected when playing a Blu-ray

Disc or DVD via a connected component.

• Check the audio setting of the component

connected to this stand, such as a Blu-ray

Disc recorder (player) or DVD player.

The surround effect cannot be obtained.

• Depending on the sound field setting and/or

input signal, surround processing may not

work. To check the input signal, press the

INPUT SELECTOR on the stand and select

the input again. When the input is switched,

the input signal type appears in the front

panel.

If “2.0ch’’ or “1.0ch” appears, the sound

source is stereo or monaural, and does not

contain surround sound.

If “5.1ch’’ appears, the sound source does

have surround sound, though not much

surround sound may be heard, depending on

the program or disk.

No sound or only a very low-level sound is

heard from the speakers.

• Press VOLUME + and check the volume

level.

• Press MUTING or VOLUME + to cancel the

muting function.

• Press SOUND FIELD +/– and check the

selected sound field.

• Depending on the source, the sound effect of

the speakers may be less noticeable.

The sound is delayed compared to the image

of the TV.

• Set “A/V SYNC” to “OFF” when “A/V

SYNC” is set to “ON.”

Connected components

There is no sound or only a very low-level

sound no matter which component is selected.

• Check that this system and components are

connected correctly and securely.

• Check that both this system and the selected

component are turned on.

There is no sound from the selected

component.

• Check that the component is connected

correctly to the audio input jacks for that

component.

• Check that the cords are fully inserted into

the jacks on both the component and this

system.

• Check that the component is selected

correctly.

• If you resume playback of a disc when

volume is maximum, there may be no sound.

In this case, turn down the volume, turn off

the system and turn on again.

Sound is interrupted or there is noise.

• Check the output audio formats supported

by this system on page 36.

Additional Information

Troubleshooting

continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony RHT-G500 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony RHT-G500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info