Bedienungsanleitung Sorel STDC (Seite 17 von 24) (Englisch)

812372

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Tmin S1

Enable/start temperature at sensor 1:

If this value on the sensor 1 (collector sensor) is exceeded and the other conditions are not fulfilled, the controller will turn on the affiliated

pump or the valve. If the temperature on the sensor 1 falls 5 °C below this value, the pump or the valve will be turned off again.

Tmin S2

Switch off temperature at sensor 2:

If this value is exceeded on the sensor 2, the controller turn off the affiliated pump or the valve. If this value on the sensor 2 is undershot and

the other conditions are fulfilled, the controller will turn on the pump or the valve.

Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided

by the customer!

In multiple storage systems, if the shut-down temperature S2 is exceeded, a downstream installed storage or storage area is switched to.

ΔT R1

On/off temperature difference for solar charge through relay R1:

If the temperature difference ΔT Solar between the reference sensors S1 and S2 is exceeded and the other conditions are fulfilled, the con-

troller will turn on the pump on the relay R1. If the temperature difference falls to ΔT Off, the pump will be turned off.

If the set temperature difference is too small, this may lead to ineffective operation depending on the system and sensor pos-

itioning. For speed regulation (" Speed control " on page 20), special switch conditions apply!

Tset On

Reference temperature sensor 1

Heating mode = 1. Value smaller than 2. value,

Cooling mod = 1. Value bigger than 2. value.

If the set switch-on value (1. Value) at sensor 1 undershot and thermostat function is approved (see also 5.5), backup heating is switched

on until temperature exceeds value for switch off (2. Value).

Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided

by the customer!

If sensor S2 is connected, S1 functions as a switch-on sensor and S2 as a switch-off sensor.

Tmax S1

Switch off temperature at sensor 1

If this value is exceeded on the sensor 1, the controller turn off the affiliated pump or the valve. If sensor 1 falls below this value again and

the other conditions are also met, then the controller switches the pump and/or valve on again.

Temperature values which are set too high can lead to scalding or damage to the system. Scalding protection must be provided

by the customer!

Thermostat periods

Here the desired periods are set in which the thermostat function is approved. For each weekday, three times can be specified, fur-

thermore, you can copy individual day to other days. The thermostat function is shut down outside of the set times.

Tmin Storage X

Switch off temperature at sensor S(X)

If this value is exceeded at sensor X then the controller switches the associated pump and/or valve off. If sensor (X) falls below this value

again and the other conditions are also met, then the controller switches the pump and/or valve on again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sorel STDC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sorel STDC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info