Bedienungsanleitung Sorel XHCC S61 (Seite 34 von 44) (Englisch)

812340

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Gylcol pump lag

After shutting down the compressor, the pump remains on for the time set here.

Cooling

In this menu, the cooling function is activated, and the mode of cooling function is set.

Heating Circuit: In the Heating Circuit modus, the heating circuit is used for room cooling. This may be a surface heating circuit or

a radiator heating circuit. For this operating mode, a room thermostat with humidity sensor is required (e.g. RC22, ° CALEON

Clima).

Air conditioning:Through the air conditioning modus, fan coils connected through the heating circuit may be activated for room

cooling.

Single: In this modus, the switch contact is switched in regards to the assigned sensor for the cooling of the measured

Temperature in order to control external air conditioning for room cooling.

Off: Cooling function is disabled.

Sensor cooling

Here the affiliated sensor is set for the cooling function in the Simple modus. If theset temperature on this sensor is exceeded, the

relay will turn on for the cooling function. If the set temperature on this sensor is exceeded bz the hysteresis, the relay will turn on

for the cooling function.

Max. flow cooling

This value is the upper limit of the reference flow temperature of the cooling.

Min. flow cooling

This value is the lower limit of the reference flow temperature of the cooling.

Cool storage

The storage can be cooled through this function.

Yes: The flow and buffer storage are cooled down to the reference flow temperature + hysteresis.

No: It is cooled down to the reference flow temperature + hysteresis, the temperature in the buffer storage is ignored.

By default, sensor S2 is set as the buffer sensor. Theassigned sensor for this function can be changed in the settings for the heat-

ing circuit 1 see " Buffer sensor " on page 28.

Dew point correction

The internal dew point curve is moved parallel with this value. The dew point calculation is used to calculate at which room tem-

perature there is an undesired condensation (precipitation) at the currently measured humidity. This calculated room temperature

will not be undershot with the cooling system and therefore represents a temperature lower limit for the cooling system.

The calculated room temperature can be moved by up to 10 °C with the dew point correction.

Example 1: You determine that there is precipitation with the default value,

so you increase this correction value.

Example 2: Condensation/precipitation can be ignored, instead a

stronger cooling system is required. You therefore decrease this correction value.

In case of reduction of the calculated temperature with the help of dew point correction condensation / perspiration / pre-

cipitation can occur, which, among other things, may cause the formation of mold.

Room reference cooling

Reference value for the temperature in the room.

The controller adjusts the flow so that this temperature is reached in the room.

If the value set here is exceeded, the relay will turn on the cooling function if this is approved for the time.

The relay of the cooling function is turned off if the reference value hysteresis is not met.

Delay

Switch delay of the heat and cooling request. In order to prevent the heat or cooling request to be activated if there are heat devi-

ations, the corresponding relay is switched up ot 5 minutes before the switch conditions occur.

Periods

Cooling activity times

Here the desired periods are set in which the cooling function is approved. For each weekday, three times can be specified, fur-

thermore, you can copy individual day to other days. The cooling function is shut down outside of the set times.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sorel XHCC S61 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sorel XHCC S61

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info