Bedienungsanleitung Soundcraft MFX12 (Seite 16 von 48) (Englisch)

611455

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

The Send may also be tapped off as an alternative pre-fade, pre-EQ direct output if

required, using a lead with tip and ring shorted together so that the signal path is

not interrupted (see below).

5 Gain

This knob sets how much of the source signal is sent to the rest of the mixer. Too

high, and the signal will distort as it overloads the channel. Too low, and the level of

any background hiss will be more noticeable and you may not be able to get enough

signal level to the output of the mixer.

Note that some sound equipment, particularly that intended for domestic use,

operates at a lower level (-10dBV) than professional equipment and will therefore

need a higher gain setting to give the same output level.

See “Initial Setup” on page 33 to learn how to set GAIN correctly.

6 Equaliser

The Equaliser (EQ) allows fine manipulation of the sound, particularly to improve

the sound in live PA applications where the original signal is often far from ideal

and where slight boosting or cutting of particular voice frequencies can really make

a difference to clarity. There are three sections giving the sort of control usually only

found on much larger mixers. The EQ knobs can have a dramatic effect, so use

them sparingly and listen carefully as you change any settings so that you get to

know how they affect the sound.

HF EQ

Turn to the right to boost high (treble) frequencies above 12kHz by up to 15dB,

adding crispness to cymbals, vocals and electronic instruments. Turn to the left to

cut by up to 15dB, reducing hiss or excessive sibilance which can occur with cer-

tain types of microphone. Set the knob in the centre-detented position when not

required.

MID EQ

There are two knobs which work together to form a SWEPT MID EQ. The lower knob

provides 15dB of boost and cut, just like the HF EQ knob, but the frequency at

which this occurs can be set by the upper knob over a range of 150Hz to 3.5kHz.

This allows some truly creative improvement of the signal in live situations, be-

cause this mid band covers the range of most vocals. Listen carefully as you use

these controls together to find how particular characteristics of a vocal signal can

be enhanced or reduced. Set the lower knob to the centre-detented position when

not required.

LF EQ

Turn to the right to boost low (bass) frequencies below 80Hz by up to 15dB, adding

warmth to vocals or extra punch to synths, guitars and drums. Turn to the left to cut

low frequencies by up to 15dB for reducing hum, stage rumble or to improve a

mushy sound. Set the knob to the centre-detented position when not required.

7 Aux Sends

These are used to set up separate mixes for FOLDBACK, EFFECTS or recording, and

the combination of each Aux Send is mixed to the respective Aux Output. For

Effects it is useful for the signal to fade up and down with the fader (this is called

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft MFX12 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info