Bedienungsanleitung Sparky BP 330E (Seite 9 von 110) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

604122

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Original instructions

breaking and chiselling in brickwork, concrete

and rocks with high efciency. In impact drilling

mode the rotary hammer equipped with adapter

and chuck 176838 (not included) can be used

as a drill for drilling in steel, wood, plastics, etc.

Power tools marked with this symbol

are equipped with a mechanism for reducing vi-

brations, decreasing them by more than 50%.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corre-

sponds to the value indicated on the name

plate with technical data of the tool.

▪ Always check the position of ON/OFF switch.

The power tool must be connected to the

power supply socket only when this switch is

in OFF position. If the plug is connected to

a receptacle while the power switch is in the

ON position, the power tool will start operat-

ing immediately, which could cause a serious

accident.

▪ Make sure that the cord and the plug are in or-

der. If the replacement of the supply cord is nec-

essary, this has to be done by the manufacturer

or his agent in order to avoid a safety hazard.

▪ In case the work area is remote from the power

source, use as short as practicable extension

cord with proper cross-section.

WARNING: Always switch off and un-

plug the power tool prior to any adjustment,

servicing or maintenance.

▪ Check that the auxiliary handle is properly

mounted and reliably tightened.

SWITCHING ON - SWITCHING OFF

Brief activation

Switching on: Press ON/OFF switch 5. (Fig.1)

Switching off: Release ON/OFF switch 5.

Continuous operation

Switching on: Press ON/OFF switch 5 and in

pressed position lock it by button 6. (Fig. 2)

Switching off: Press ON/OFF switch 5 once and

release it immediately.

At low temperatures, demolishing with the pow-

er tool must begin only after it was operated for

about 3 minutes at no-load mode.

INSERTING OF SDS-Plus TOOL

Clean and grease the shank of the accessory,

before placing it into the socket! (Fig.3)

Pull backward the sleeve 3 of the socket 1

(Fig. 4a) and insert the SDS-Plus bit until stop.

Ensure that the socket grooves correspond to

the shank channels, and then release the sleeve

to x the bit. (Fig. 4b)

To remove the bit, pull the sleeve 3 back, and

then take the bit out. (Fig.5)

WARNING: Never use drill bits with

diameter exceeding the indicated to avoid

overloading the power tool..

SELECTINGTHESPEED,FREQUENCY

AND IMPACT ENERGY

Rotate the regulator 7 to choose a position ap-

propriate for the processed material. It is recom-

mended to use the operation modes listed in the

table.

Application

Regulator

position

Rotation

speed

Impactrate Impactenergy

Boring with core cutters A-D 380-650 min

-1

1560-2660 min

-1

1.5-3.6 J

Render / Light construction

materials / Bricks / Chiselling

tiles

D-Е 650-740 min

-1

2660-3030 min

-1

3.6-4.3 J

Chiselling and drilling concrete

F 830 min

-1

3400 min

-1

5 J

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sparky BP 330E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info