Bedienungsanleitung Sparky BP 750CE (Seite 9 von 114) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

604120

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

Original instructions

This power tool is equipped with a

mechanism for reducing vibrations, decreasing

them by more than 30%.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corre-

sponds to the value indicated on the name

plate with technical data of the tool.

▪ Always check the position of ON/OFF switch.

The power tool must be connected to the

power supply socket only when this switch is

in OFF position. If the plug is connected to

a receptacle while the power switch is in the

ON position, the power tool will start operat-

ing immediately, which could cause a serious

accident.

▪ Make sure that the cord and the plug are in

order. If the replacement of the supply cord is

necessary, this has to be done by the manu-

facturer or his agent in order to avoid a safety

hazard.

WARNING: Always switch off and un-

plug the power tool prior to any adjustment,

servicing or maintenance.

▪ In case the work area is remote from the pow-

er source, use as short as practicable exten-

sion cord with proper cross-section.

▪ Check that the auxiliary handle is properly

mounted and reliably tightened.

SWITCHING ON - SWITCHING OFF

▪ Switching on: Push and hold down switch 7.

▪ Switching off: Release switch 7.

At low temperatures, demolishing with the pow-

er tool must begin only after it was operated for

about 3 minutes at no-load mode.

WARNING: Upon overloading the ma-

chine with 30% the red light-emitting diode 10

will glow. The machine must not be operated

conti nuously in this mode.

SELECTING THE SPEED, FREQUENCY

AND IMPACT ENERGY

Rotate the regulator 8 to choose a position

appropriate for the processed material. The

constant electronics maintain the speed, the

frequency and the impact energy constant, in-

dependently of the load, thus ensuring steady

operation mode. It is recommended to use the

operation modes listed in the table.

Rotate the regulator 8 from position A to position

F to increase the speed, the frequency and the

impact energy. The indicator 9 shall blink with

green light.

To choose High Power mode, rotate the regula-

tor 8 to position G. This mode is specied by in-

creased impact energy up to 13 J. The indicator

9 shall glow with constant green light.

WARNING: Using High Power mode

is recommen ded only when chiselling (ham-

mer mode), and for brief operation in impact

drilling mode. Continuous operation in impact

drilling mode shall result in operator’s quick

fatigue and increased wear-out of the ma-

chine.

SELECTING THE OPERATION MODE

The switching of operation modes can be per-

formed when the machine is not operating.

This rotary hammer can be used in two opera-

tion modes:

Application

Regulator

position

Rotation

speed

Impact rate

Single impact

energy

Render / Light construction

materials

A-B 120-145 min

-1

1150-1450 min

-1

4-5 J

Chiselling tiles C 175 min

-1

1700 min

-1

7 J

Bricks D 200 min

-1

1950 min

-1

8 J

Drilling in concrete E-F 225-250 min

-1

9-10 J

Chiselling concrete G 2800 min

-1

13 J

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sparky BP 750CE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info