Bedienungsanleitung Sparta D-rule M8Tb - 2021 (Seite 18 von 230) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch)

779128

Zoom out

Zoom in

Vorherige Seite

1/230

Nächste Seite

English – 3

ternal battery. The state of charge of the eBike battery can

also be checked on the LEDs of the battery itself.

Each bar of the battery symbol on the indicator (i) repres-

ents approximately 20% of the capacity:

The eBike battery pack is fully charged.

The eBike battery pack should be recharged.

The LEDs of the battery charge indicator on the

battery go out. The capacity for assisting the

drive has been used up, and assistance is

gently switched off. The remaining capacity is

made available for the lighting and the on-

board computer. The indicator flashes. The ca-

pacity of the eBike battery is enough for about

two hours of lighting. This does not account for

other consumers (e.g. automatic gearbox, char-

ging external devices at the USB port).

If the on-board computer is removed from the holder (4),

the last displayed state of charge of the battery is saved. If

an eBike is powered by two batteries, the battery charge in-

dicator (i) displays the state of charge of both batteries.

OFF

MPH

KM/H

If an eBike has two batteries inserted into

it and both batteries are charged on the

bike, the charging progress of both bat-

teries will be indicated on the display

(the left-hand battery pack is being

charged in the illustration). You can also

tell by the flashing indicator on the bat-

tery which of the two batteries is being

charged.

Setting the assistance level

On the operating unit(9), you can set the level of assistance

you want the eBike drive to provide you with while pedalling.

The assistance level can be changed at any time, even while

cycling.

Note: In some models, the assistance level may be preset

and cannot be changed. There may also be fewer assistance

levels available than stated here.

The following assistance levels are available as a maximum:

–OFF: Motor assistance is switched off. The eBike can just

be moved by pedalling, as with a normal bicycle. The

push assistance cannot be activated at this assistance

level.

–ECO: Effective assistance with maximum efficiency, for

maximum range

–TOUR: Steady assistance, long range for touring

–SPORT/eMTB:

SPORT: Powerful assistance, for mountain biking and

cycling in urban traffic

eMTB: Optimum assistance whatever the terrain, rapid

acceleration when starting from a standstill, improved dy-

namics and top performance (eMTB only available in

combination with the drive units BDU250P CX, BDU365,

BDU450 CX and BDU480 CX. A software update may be

required.)

–TURBO: Maximum assistance even at high pedalling

speeds, for sport cycling

To increase the assistance level, press the + button(12) on

the operating unit repeatedly until the required assistance

level appears on indicator (b). To decrease the assistance

level, press the – button(11).

The requested motor output is displayed in the indicator (a).

The maximum motor output depends on the selected assist-

ance level.

When the on-board computer is removed from the holder

(4), the assistance level that was last displayed is saved; the

motor output indicator (a) remains empty.

Interaction between the eBike system and gear-

shifting

The gear-shifting should be used with an eBike drive in the

same way as with a normal bicycle (observe the operating in-

structions of your eBike on this point).

Irrespective of the type of gear-shifting, it is advisable that

you briefly stop pedalling when changing gear. This will aid

the gear change and reduces wear on the powertrain.

By selecting the correct gear, you can increase your speed

and range while applying the same amount of force.

For this reason, follow the gear change recommendations

provided by the indicators (g) and (h) on your display. If in-

dicator (g) is displayed, you should change to a higher gear

with lower cadence. If indicator (h) is displayed, you should

select a lower gear with higher cadence.

Switching bike lights on/off

On the model on which the lighting is powered by the eBike

system, the front and rear lights can be switched on and off

at the same time via the on-board computer using the bike

light button(2).

Check that your bike lights are working correctly before

every use.

When the lighting is switched on, <Lights on> appears and

when the lighting is switched off, <Lights off> appears for

approx. 1s on the text indicator (d). The lighting symbol (c)

is displayed when the light is on.

The on-board computer saves the light status and activates

this saved status accordingly after a restart.

Switching the bike lights on and off has no effect on the

backlighting of the display.

Switching the push assistance on/off

The push assistance aids you when pushing your eBike. The

speed in this function depends on the selected gear and can

reach a maximum of 6km/h. The lower the selected gear,

the lower the speed of the push assistance function (at full

power).

uThe push assistance function must only be used when

pushing the eBike. There is a risk of injury if the wheels

of the eBike are not in contact with the ground while using

the push assistance.

Bosch eBike Systems 1 270 020 XBI | (11.03.2020)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sparta D-rule M8Tb - 2021 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info