Bedienungsanleitung Spartherm Mini H2O (Seite 35 von 44) (Englisch)

810451

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

GB 35

Shifting the stop to 100 mm reduced opening height

This setting can be used if the flue gas system is not suitable for open

operation when putting more wood on the fire. By reducing the opening

height of the door, the air mass flow rate is reduced.

1. Close the elevating door, so that the fastening screws can be reached.

2. Unscrew the M5x10 threaded screws an both sides of the device with a

4 mm Allen wrench (ball head).

3. Pull off the door stop in the direction of the red arrow. It is possible that

it may have seized slightly and must be "levered off" from below with a

slot-head screwdriver.

4. Insert the door stop with the long bracket toward the front of the device.

Ensure that the door stops are not swapped out.

3. INITIAL COMMISSIONING

Heat generation systems must only be produced and installed by specialised

companies. The initial commissioning must only be executed by an expert

employee of the installation company. A certificate confirming proper instal-

lation and proper adjustment / function of all control components and safety

components must be given to the owner / operator of the system.

The initial commissioning must only be executed after all neces-

sary components are connected and all necessary safety devices

are integrated and functional. Before the stove / fireplace insert is

placed in service, it must be filled and ventilated on the heating side

(heating network) and water side (thermal discharge safety device;

safety heat exchanger). After the filling process, check all hydraulic

connections for leaks. Operation without a water-side connection

results in irreparable damage and invalidates any warranty claims!

The first four firings must each be executed with max. 2.0 kg/hour of

dry and thin wood (max. circumference 25 cm). Through this measure

the fireplace insert, the chamotte and the vermiculite are slowly tempered

and thus the moisture that may be present due to storage, transport, etc. is

slowly dissipated. If this does not occur, contamination of the area between

the glass panes, as well as tearing of the chamotte are possible.

Attention: Underneath the fireplace insert up to 0.5 litres of concentrate

can escape! This is not a leak!

The owner must be instructed in detail concerning the operation, function

and maintenance of the overall system, including all supplemental compo-

nents. In addition, the measures for maintaining safe operation of the sys-

tem must be communicated to the owner. The executed instruction must

be documented in the commissioning protocol! The installation and

operating instructions must always be kept in good condition in the vicinity

of the H2O fireplace insert where they can be easily accessed. Additional

Fig. 7b Fig. 7b

*The door hood has been removed only for the purpose of better documentation.

Left device side Right device side

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Mini H2O Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Mini H2O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info