Bedienungsanleitung Spartherm Nova E H2O (Seite 15 von 28) (Englisch)

810449

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GB 15

2.11 CHIMNEY CONNECTION / CONNECTING PIECES

The Nova E H2O is connected to the chimney with the connecting pieces

made from steel sheet at least 2 mm thick. These connecting pieces

must satisfy the requirements specified in DIN 1298 and DIN EN 1856-

2, and must be connected to the chimney / flue gas system in accord-

ance with the requirements specified in DIN 18160 or the country-specific

regulations. It must be ensured that the flue gas pipe takes the shortest

possible route upwards towards the chimney. The number of bends in the

flue gas pipe should be kept to a minimum. In addition, the flue gas pipe

must be connected to the chimney with a bricked-in wall lining and sealed.

If necessary, the flue gas pipe must be fastened with clamps to ensure

adequate fixation. The connecting pieces must be sealed if necessary! If the

flue gas pipe is routed through components with flammable building materi-

als, the flue gas pipe must be insulated as specified in the regulations. The

connecting line must always be mounted in such a manner that it is possible

to clean the connecting line at any time.This must be ensured through a suf-

ficient number of cleaning openings. A gauge connection must be installed

so that it is accessible for determination of the negative chimney pressure

in the connecting line.

2.12 INSTALLATION OF ROTATING DISC / AIR

ADJUSTMENT LEVER / SERVOMOTOR FOR

S-THERMATIK

After delivery, it may be necessary to mount the rotating disc through the

combustion chamber in the floor area of the tiled stove (e.g. device design

with S-Thermatik). Installation is not executed in the factory because the

star adapter (frictional connection between servomotor and rotating disc),

as well as the servomotor for the S-Thermatik project downwards out of

the device. These components would be damaged through transport and

installation.

For installation, removal of the front combustion chamber chamotte (cha-

motte brick no.: 7 and 8 Fig. 4) and of the combustion chamber floor are

necessary. Installation of the air mechanism must be executed as shown

in Fig. 3a. The air adjustment lever must be in the „closed“ position (air

adjustment lever at the left stop), so that the primary ventilation damper

can be inserted. After installation, the function of the air controller must be

checked before installation of the combustion chamber floor. For this, the

inspection opening in the front chamfer of the combustion chamber bowl

must be opened. Through this opening, it must be possible to determine the

opening of the primary ventilation damper when the air adjustment lever

is in the right position. If the air adjustment lever is turned to the left, the

primary ventilation damper must close.

Star adapter

for frictional

connection

Rotating disc

VA slide plate

Bores for holder of the servomotor

(only for S-Thermatik). The support

of the servomotor is installed through

the large cut-out in the base plate.

Base plate

The bore of the articulated

arm must be fitted on the

bolt of the air adjustment

lever.

Fig. 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Nova E H2O Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Nova E H2O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info