Bedienungsanleitung Spartherm Nova E H2O (Seite 20 von 28) (Englisch)

810449

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GB 20

5.1 CLEANING THE HEAT EXCHANGER

The heat exchanger can only function at full efficiency if it is regularly

and properly cleaned and serviced. Cleaning must always be executed in a

cooled-down state! As the heat exchanger directly cools down the flue gases

of the Nova E H2O fireplace insert, and this unavoidably results in deposits

on the surfaces of the heat exchanger, these surfaces must be cleaned with

the provided brush on a regular basis. The frequency of cleaning depends

on several factors (use intensity, duration of burning, fuel, chimney draught,

etc.) and a general statement concerning frequency cannot be made.

Initially, we recommend cleaning approximately every 4 weeks. If heavy

contamination does not occur, the interval can be extended. The cleaning

intervals must be adapted to the local conditions. With the use of dry fire-

wood, a functional return flow temperature boost and compliance with our

recommendations, the cleaning intervals can be significantly extended.After

the heating season ends, thorough cleaning of all components is necessary.

The heat exchanger is always cleaned through the combustion chamber

of the fireplace insert. For this, the fireplace door must be opened and the

flame deflector plates (flame baffle plate) must be taken out of the combus-

tion chamber. Next, the thermally activated flue gas damper is removed

through the combustion chamber (see Fig. 6a). For this, the damper is tilted

slightly by the handle and taken out in a downwards direction. Clean the

thermal flue gas damper with a hand brush. Then the turbulators (bent

pieces of sheet metal in the flue gas pipes) are pulled downwards and out

into the combustion chamber with pliers. Subsequently, the heat exchanger

pipes and the middle channel, as well as the outer surfaces of the heat

exchanger, must be cleaned with the provided brush or a hand brush. Then

the deposits fall automatically into the combustion chamber and they can

be removed with standard aids (ash shovel, ash broom or an ash vacuum).

After cleaning, assembly is executed in the reverse sequence.

First, hook in the thermal flue gas damper (introduce diagonally from below

and place on the supports). Then slide in the turbulators (these do not

require a specific direction) and insert the flame baffle plates in such a

manner that the flue gas gap is on the rear of the device.

ASupport

BAutomatic flue gas damper with handle

C8 turbulators in the heat exchanger pipes

DHandle - flue gas damper

ENo turbulators in the rear heat exchanger

pipes

Fig. 6a

Fig. 6b

5.2 CLEANING THE DOUBLE GLAZING

The operator must only clean the double glazing on the combustion chamber

side and the setup room side in accordance with the instructions in the

operating manual. If the inner panes in the hollow space are contaminated,

then cleaning must only be executed by the customer service organisation

or a trained specialised company. In operation, a slight bright shimmer may

be seen between the glass panes. However these deposits do not constitute

grounds for complaint.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Nova E H2O Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Nova E H2O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info