Bedienungsanleitung Spektrum DX8 (Seite 40 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite



Note: Cages have been removed for clarity.

Step 4. Locate the gimbal that currently has the throttle friction engaged (mode

2 is the right gimbal from the rear). Unscrew the silver throttle tension

screw until the friction strap is no longer in contact with the friction

portion of the gimbal. The gimbal should now move freely. Now on

the opposite gimbal locate the friction strap you desire (ratcheted or

smooth). Screw in the corresponding screw until the throttle tension

starts to engage.

Note: Cages have been removed for clarity.



Note: When changing modes that require the throttle and elevator to be

moved from one side to the other (mode 1 to mode 2 for example) it is

recommended that that the elevator and throttle stick be held fully up or

down while the elevator centering screw is fully tightened or loosened.

This will reduce the load on the elevator centering mechanism making it

easier to properly adjust the centering screw.

Step 5. Locate the gimbal that currently has the elevator centering spring

engaged (mode two is the left gimbal from the rear). Using a Phillips

screwdriver, fully tighten the elevator centering screw as show below.

This disengages the elevator centering spring. Now locate the elevator

centering screw on the opposite gimbal and back this screw out until

the elevator centering lever is fully engaged.

Note: Cages have been removed for clarity.

Step 6. Throttle limiting wedges are used to limit the maximum throttle travel

for improved ergonomics. When switching modes that swap elevator

and throttle positions the throttle limiting wedges must also be moved.

Using a Phillips screwdriver, you will need to unscrew the two upper

circuit boards and move these upward to access the upper inner screw

of the cages. Now unscrew the eight Phillips screws that retain the

cages and remove the cages.

Step 7. Most pilots prefer having a throttle with less stroke as it provides a

more natural feel when giving rudder commanded (mode 2) at full

or low throttle. When changing throttle position from right to left it’s

necessary to switch the throttle limiting wedges positions. Using a

Phillips screwdriver remove the throttle limiting wedges from their

current position and reinstall them on the opposite gimbal.

Step 8. Reinstall the gimbal cages and upper circuit boards, then the back of

the transmitter. Be careful not to pinch wires or the rubber side grips.

Tighten the 6 Phillips head screws then reinstall the rear and side grips.



When making a mode conversion, the programming must also be changed and

when changing throttle elevator positions the transmitter must be recalibrated in

the systems setting screen.



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.

Highlight System Settings then press the roller to access the System Settings

function. The System Settings screen will appear.

To Select a Mode

In the Systems Settings screen rotate the roller to highlight Mode then press the

roller to select the Mode function.

Rotate the roller to select the desired mode then press the roller to accept the

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info