Bedienungsanleitung Spektrum SPM 18000 - DX18 (Seite 11 von 42) (Englisch)

606958

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

11SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL

SD CARD

X-PLUS™

Installing the SD Card

The included SD Card enables you to:

• Import (copy) models from another DX18 transmitter

• Export (transfer) models to another DX18 transmitter

• Update AirWare™ software in the transmitter

To install the SD Card:

1. Power off the transmitter.

2. Remove the battery door.

3. Press the SD Card into the card slot with the card label

facing upward.

4. Install the battery door.

Exporting the Transmitter Serial Number

to the SD Card

Exporting the transmitter serial number to the SD Card allows

you to copy and paste the serial number into the registration

screen at community.spektrumrc.com .

To export the serial number:

1. Press and hold the scroll wheel while powering the

transmitter on until the System Setup list appears.

2. Scroll to the System Settings menu. Press the scroll wheel

once to open the menu.

3. Select NEXT on the System Settings and Extra Settings

screens.

4. When the Serial Number screen appears, select EXPORT.

5. Power off the transmitter and remove the SD Card from the

transmitter.

6. Insert the SD Card in your computer and open the .txt ﬁ le on

the card.

7. Copy and Paste the serial number into the Registration

screen on the Spektrum Community site ( community.

spektrumrc.com ).

X-Plus Channels and Failsafe

Failsafe is not supported for servos connected to the X-Plus

Module. We recommend that no failsafe should be expected or

attempted for a servo connected through the X-Plus Module.

However, servos connected to the X-Plus Module will hold last

command in the event of a failsafe condition.

To Activate X-Plus

1. Open the Frame Rate Menu in System Setup.

2. Scrolll to X-Plus and press the scroll wheel to activate. The

X-Plus Inputs screen is now active in the Channel Assign

menu.

AUX6 and AUX7 channels are available on 12-channel receivers

when X-Plus is active. AUX6 and AUX7 are 2048 resolution and

22ms frame rate (12-channel receivers only).

Channels X+1 and X+2 are duplicate channels of channels 11

and 12 on a 12 channel receiver with X-Plus active. If chan-

nels 11 and 12 require any adjustment for travel adjust, servo

reversing, sub trim or any other function, adjust channels X+1

and X+2. Note that channels 11 and 12 will also show on the

X-Plus monitor as channels X+1 and X+2.

If you select 11ms frame rate before you activate X-Plus, the

transmitter reverts to 22ms frame rate when X-Plus is active.

CAUTION: Do NOT connect throttle or any primary

control surface to the X-Plus Module. The X-Plus chan-

nels are intended to be used for auxiliary functions only. X-Plus

channels have a resolution of 512 and variable latency from

22ms to about 88ms. When X-Plus is active, the ﬁ rst 10 chan-

nels default to 22ms.

Refer to community.spektrumrc.com for more information about

X-Plus options.

from Channel Assign menu

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum SPM 18000 - DX18 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum SPM 18000 - DX18

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info