Bedienungsanleitung Stanley FMC675 (Seite 6 von 96) (Alle Sprachen)

622601

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-off button

3. Shoe

4. Battery

5. Blade clamp collar

Fig. A

6. Charger

7. Charging indicator

Assembly

Warning! Before assembly, remove the battery from the tool

and make sure that the saw blade has stopped. Used saw

blades may be hot.

Fitting the saw blade (g. C)

u Hold the tool away from the body

u Rotate the blade clamp collar (5) in the direction shown in

gure C

u Insert the shank of the blade (9) fully into the blade clamp

collar (5).

u Release the blade clamp collar (5) to lock the blade into

position

Note: The blade can be installed with the teeth up to assist in

ush cutting

Removing the saw blade (g. C)

Warning! Burn hazard: Do not touch the blade immediately

after use. Contact with the blade may result in personal injury.

u Rotate the blade clamp collar (5) to the release position

u Remove blade (9)

Lock-off button

The tool is equipped with a switch lock-off feature to prevent

unintentional operation.

u To lock: push the lock-off button (2) to the locked position

u To un-lock: push the lock-off button (2) to the un-locked

position .

Fitting and removing the battery (g. B)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release buttons (8) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u To charge the battery (4), insert it into the charger (6). The

battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (7) will ash green (slowly).

The charge is complete when the charging indicator (7) lights

green continuously. The charger and the battery can be left

connected indenitely with the LED illuminated. The LED will

change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging

indicator (7) will be lit as long as the battery is connected to

the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (7) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (4).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC675 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info