Bedienungsanleitung Stanley FMC675 (Seite 7 von 96) (Alle Sprachen)

622601

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

Switching on and off

The variable speed on/off switch offers a choice of speeds for

greatly improved cutting rates in various materials.

u To switch the tool on, squeeze the variable speed on/off

switch (1).

u To switch the tool off, release the variable speed on/off

switch (1).

Sawing

u Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u If possible, work with the shoe (3) pressed against the

workpiece. This will improve tool control and reduce tool

vibration, as well as prevent the blade from being

damaged.

Hints for optimum use

Sawing wood

u Clamp the workpiece securely and remove all nails and

metal objects.

u Holding the tool with both hands, work with the shoe (3)

pressed against the workpiece.

Flush cutting

The compact design of the reciprocating saw motor housing

and pivoting shoe permit close cutting to oors, corners and

other difcult areas.

To maximize ush cutting capabilities:

u Insert the blade shaft into the blade clamp with the teeth of

the blade facing up.

u Adjust the angle of the handle on the tool so you are as

close to the work surface as possible.

Sawing metal

Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal. Use a

ne-tooth saw blade for ferrous metals and a coarser saw

blade for non-ferrous metals.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Pocket cutting in wood

u Measure and mark the required pocket cut.

u Fit a saw blade suitable for pocket cutting.

u Rest the shoe (3) on the workpiece in such a position that

the blade forms an appropriate angle for the pocket cut.

u Switch on the tool and slowly feed the blade into the

workpiece. Make sure that the shoe (3) remains in contact

with the workpiece at all times.

Cutting branches

Branches up to 25 mm in diameter can be cut with this tool.

Warning! Do not use the tool while in a tree, on a ladder or on

any other unstable surface. Be aware of where the branch will

fall.

u Cut downward and away from your body.

u Make the cut close to the main branch or tree body.

Vertical cutting

The tool allows close cutting to corners and other difcult

areas.

u Insert the shank of the saw blade into the blade holder

with the teeth of the blade facing upward.

u Hold the tool with the shoe (3) facing downward so that

you are as close to the work surface as possible.

u Cut forward and away from your body.

Accessories

The performance of your tool depends on the accessory used.

Stanley Fat Max accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

Blades

The saw will accept a blade up to 30 cm long. Always use the

shortest blade suitable for your project but long enough to

keep the blade cutting through the material. Longer blades are

more likely to be bent or damaged during use. During

operation some longer blades may vibrate or shake if the saw

is not kept in contact with the workpiece.

Maintenance

Your Stanley Fat Max tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC675 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info