Bedienungsanleitung Stanley FMC761 (Seite 10 von 172) (Alle Sprachen)

622595

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

(Original instructions)

Fitting and removing hubbed wheels and cups

Hubbed wheels and cups install directly on the M14 threaded

spindle (11).

Caution! To reduce the risk of personal injury, wear work

gloves when handling wire brushes and wheels. They can

become sharp.

Caution! To reduce the risk of damage to the tool, wheel

or brush must not touch guard when mounted or while

in use. Undetectable damage could occur to the accessory,

causing wires to fragment from accessory wheel or cup.

Fitting

u Thread the hubbed wheel or cup on to the spindle (11) by

hand.

u Keep the spindle lock (4) depressed and tighten the hub of

the wheel or cup with a wrench.

Removing

u Keep the spindle lock (4) depressed and loosen the hub of

the wheel or cup with a wrench.

u Remove the wheel or cup from the spindle (11).

Fitting and removing the battery (g. G)

u To t the battery (7), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release buttons (23) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

u Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

u Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Charging the battery (g. A)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u To charge the battery (7), insert it into the charger (9).

The battery will only t into the charger in one way. Do

not force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (10) will blink.

The charge is complete when the charging indicator (10)

switches to continuously on. The charger and the battery can

be left connected indenitely. The LED will switch on as the

charger occasionally tops up the battery charge.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the charg-

ing indicator (10) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (7).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 30 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Switching on and off

u To switch on, slide the lock off switch (1) forward then

press and hold the trigger switch (2).

u To switch off, release the trigger switch (2).

Warning! Do not switch the tool on or off while under load.

Warning! Always slide the lock off switch (1) backwards to the

locked position when the tool is not in use.

Hints for optimum use

u Firmly hold the tool with one hand around the side handle

and the other hand around the main handle.

Surface grinding with grinding wheels

u Allow the tool to reach full speed before touching the tool

to the work surface.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC761 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info