Bedienungsanleitung Stanley FMC761 (Seite 11 von 172) (Alle Sprachen)

622595

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ENGLISH

(Original instructions)

u Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

u Maintain a 20˚ to 30˚ angle between the tool and work

surface.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Edge grinding with grinding wheels

Wheels used for cutting and edge grinding may break or

kick back if they bend or twist while the tool is being used

to do cut-off work or deep grinding. To reduce the risk of

serious injury, limit the use of these wheels with a standard

Type 27 guard to shallow cutting and notching (less than 1/2

inch (13mm) in depth). The open side of the guard must be

positioned away from the operator. For deeper cutting with

a Type 1 cut-off wheel, use a closed Type 1 guard. See the

Grinding and cutting chart which can be found at the back of

language section.

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to the work surface, allowing the

tool to operate at high speed. Grinding rate is greatest

when the tool operates at high speed.

u Position yourself so that the open-underside of the wheel

is facing away from you.

u Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

wheel breakage. Edge grinding wheels are not designed

to withstand side pressures caused by bending.

u Remove the tool from the work surface before turning

the tool off. Allow the tool to stop rotating before laying it

down.

Do not use edge grinding/cutting wheels for surface grinding

applications because these wheels are not designed for side

pressures encountered with surface grinding. Wheel breakage

and injury may result.

Surface nishing with sanding ap discs

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Sanding rate is greatest when

the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Using sanding backing pads

Choose the proper grit sanding discs for your application.

Sanding discs are available in various grits. Coarse grits yield

faster material removal rates and a rougher nish.

Finer grits yield slower material removal and a smoother

nish.

Begin with coarse grit discs for fast, rough material removal.

Move to a medium grit paper and nish with a ne grit disc for

optimal nish.

u Coarse 16 - 30 grit

u Medium 36 - 80 grit

u Fine Finishing 100 - 120 grit

u Very Fine Finishing 150 - 180 grit

u Allow the tool to reach full speed before touching tool to

the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Sanding rate is greatest when

the tool operates at high speed.

u Maintain a 5˚ to 15˚ angle between the tool and work

surface. The sanding disc should contact approximately

one inch (25mm) of work surface.

u Move the tool constantly in a straight line to prevent burn-

ing and swirling of work surface. Allowing the tool to rest

on the work surface without moving, or moving the tool in

a circular motion causes burning and swirling marks on

the work surface.

u Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying it down.

Using wire cup brushes and wire wheels

Wire wheels and brushes can be used for removing rust, scale

and paint, and for smoothing irregular surfaces.

Note: The same precautions should be taken when wire

brushng paint as when sanding paint.

u Allow the tool to reach full speed before touching the tool

to the work surface.

u Apply minimum pressure to work surface, allowing the tool

to operate at high speed. Material removal rate is greatest

when the tool operates at high speed.

u Maintain a 5˚ to 10˚ angle between the tool and work

surface for wire cup brushes.

u Maintain contact between the edge of the wheel and the

work surface with wire wheels.

u Continuously move the tool in a forward and back motion

to avoid creating gouges in the work surface. Allowing the

tool to rest on the work surface without moving, or moving

the tool in a circular motion causes burning and swirling

marks on the work surface.

u Remove the tool from the work surface before turning

the tool off. Allow the tool to stop rotating before setting it

down.

Use extra care when working over an edge, as a sudden

sharp movement of grinder may be experienced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC761 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info