Bedienungsanleitung Stanley FMCR001 (Seite 7 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720673

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

(Original instructions)

14. Coin cell battery door

15. Auxillary port

Use

Operating the Radio

Your radio is equipped with memory capacity in order to store

the time and your selected preset channels. When the radio is

in the OFF position. This memory capacity is powered by one

coin cell battery which is included with the radio.

Installing coin cell battery (Fig. A)

Warning! Do not ingest the battery, chemical Burn Hazard.

This product contains a coin/button cell battery. If the coin/

button cell battery is swallowed, it can cause severe internal

burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using

the product and keep it away from children.

If you think batteries might have been swallowed or placed

inside any part of the body, seek immediate medical attention.

Warning! Danger of explosion if battery is incorrectly

replaced. When replacing battery, replace it with the same or

equivalent type CR2032. Observe correct polarity (+ and –)

when replacing batteries. Do not store or carry batteries so

that metal objects can contact exposed battery terminals.

Warning! To reduce the risk of serious personal injury, turn

tool off and disconnect radio from power source before

installing/changing coin cell battery.

u On the battery door (14) on the back of the unit, turn

the screw (16) counterclockwise to remove. Screw will

remain captive in the door.

u Pull the battery door open.

u Install the coin cell battery according to the diagram

inside the coin cell battery area.

u Replace the battery door, insert the screw and tighten.

Note: To reset the LCD display, clock, and remove the

coin cell battery for few minute and then re-install.

Follow this procedure if the screen seems to lock in place and

tighten securely.

Installing and removing the battery pack (Fig. B, C)

To install the battery pack (17) into the charger/radio, align the

battery pack with the rails on the battery port (13) and slide

it into the radio until the battery pack is latched and rmly

seated and you have ensured that it does not disengage.

To remove the battery pack from the radio, press the release

button (18) and rmly pull the battery pack out.

Charging a battery

Stanley Fat Max chargers are designed to charge Stanley Fat

Max chargers battery packs. When the radio is plugged in it

will charge the installed battery.

u Plug the charger radio into an appropriate outlet before

inserting a battery pack.

u Insert the battery pack (17) into the charger radio,making

sure the battery pack is fully seated in the battery slots

(Figure B).

The LED will ash indicating that the battery

is being charged.

The completion of charge is indicated by the

LED remaining on continuously. The pack is

fully charged and may be used at this time or

left in the charger.

u Recharge discharged batteries as soon as possible after

use or battery life may be greatly diminished. For longest

battery life, do not discharge batteries fully.

It is recommended that the batteries be recharged after

each use.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged

battery. The LED ashes in the pattern

indicated on the label. If you see this bad

battery blink pattern, do not continue to charge the battery.

Return it to a service center or a collection site for ecycling.

Hot/cold pack delay

When the charger detects a battery that is

excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life.

The light ashes in the pattern indicated on the label.

Leaving the battery in the charger

The charger and battery pack can be left connected with

the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged. This charger features

an automatic tune-up mode which equals or balances the

individual cells in the battery pack to allow it to function at

peak capacity. Battery packs should be tuned up weekly or

whenever the battery no longer delivers the same amount

of work. To use the automatic tune-up mode, place the

battery pack in the charger and leave it for at least 8 hours.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMCR001 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info