Bedienungsanleitung Stanley FME340 (Seite 6 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

622180

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

(Original instructions)

u Slide the shoe plate forward to release it from the 0° posi-

tive stop position.

u Set the shoe plate to the desired bevel angle. Use a

protractor to verify angle accuracy.

u Push the shoe beveling lever (6) back towards the saw to

lock the shoe plate (5).

Note: The shoe can be beveled to the left or to the right and

has detents at 15°, 30° and 45°.

To reset the shoe for straight cuts:

u Pull the shoe beveling lever (6) out and away from the

saw to unlock the shoe plate (5).

u Rotate shoe to an angle of approximately 0° and then pull

shoe backwards to engage the 0° positive stop.

u Push the shoe beveling lever back (6) towards the saw to

lock the shoe plate (5).

Cutting action (g. F)

This jig saw is equipped with four cutting actions, three orbital

and one straight. Orbital action has a more aggressive blade

motion and is designed for cutting in soft materials like wood

or plastic. Orbital action provides a faster cut, but with a less

smooth cut across the material. In orbital action, the blade

moves forward during the cutting stroke in addition to the up

and down motion..

Warning! Metal or hardwoods should never be cut in orbital

action.

u Move the cutting action lever (8) between the four cutting

positions: 0, 1, 2, and 3..

u Position 0 is straight cutting.

u Positions 1, 2, and 3 are orbital cutting.

u The aggressiveness of the cut increases as the lever is

adjusted from one to three, with three being the most

aggressive cut.

LED worklight

The tool is equipped with an LED worklight (10) which projects

on the cutting path.

u The LED worklight (10) will come on when the trigger

switch (1) is pressed and will go off when the trigger

switch (1) is released..

Sawing

u Always hold the tool with both hands.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

u If possible, work with the shoe plate (5) pressed against

the workpiece. This will improve tool control and reduce

tool vibration, as well as prevent the blade from being

damaged.

Hints for optimum use

General

u Use a high speed for wood, a medium speed for alu-

minium and PVC and a low speed for metals other than

aluminium.

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may

occur on the surface closest to the shoe plate.

u Use a ne-tooth saw blade.

u Saw from the back surface of the workpiece.

u To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Sawing metal

Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal. Use a ne-

tooth saw blade for ferrous metals and a coarser saw

blade for non-ferrous metals.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Accessories

The performance of your tool depends on the accessory used.

Stanley Fat Max accessories are engineered to high quality

standards and designed to enhance the performance of your

tool. By using these accessories you will get the very best

from your tool.

This tool is suitable both for U-shank and T-shank saw blades.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance, switch off and

unplug the tool.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Occasionally apply a drop of oil to the axle of the blade

support roller.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME340 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info