720659
5
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
5
ENGLISH
(Original instructions)
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Features
This tool includes some or all of the following features.
1. Roller bracket
2. Roller bracket adjusting screw
3. Leg locking handle
4. Leg locking pin
5. Fxing arm
6. Carrying handle
7. Scalable bracket
8. Locking pin
Use
Preparing the stand (Fig. A)
u Lay down the stand’s top surface on the oor with the
folded legs on top.
u Push in a leg locking pin (4) and rotate that leg until the
locking pin clicks into place.
u Repeat with the remaining three legs.
u Lift the stand.
u Check to ensure the stand is stable and all locking pins
are in position.
Assembling the roller brackets (Fig. B &C)
The roller brackets help balance the workpiece during cutting
operations.
To assemble the roller brackets:
u Screw in the locking screws (8) through the locking screw
holes at both ends of the stand, as shown in Figure B.
u Insert the roller brackets (1) into the square holes at both
ends of the stand, Figure C.
u Place and tighten the adjustment screws (2) at both ends
of the stand, Figure C.
Attaching the mitre saw with supporting arms to
stand (Fig. D, E, F & G)
Prepare supporting arms (Fig. D)
u Insert two M8x60 Bolts and washers (9) into each
supporting arm.
Warning! Turn off tool switch and disconnect power before
mounting to the stand. Unintended startup during assembly
can cause injury.
To ensure balance and stability when using the saw, all four
corners of the saw must be bolted to the mounting arms
before use. Make sure bolts do not extend above the table of
the mitre saw.
Attaching mitre saw to supporting arms (Fig. E)
The saw has four holes that line up with the slots in the
supporting arms. See Figure E.
u Place the supporting arms downward.
u Lift one side of the saw and place a supporting arm
underneath, aligning the socket head cylinder cap screws
with mitre saw mounting holes, as shown in gure E.
u Seat the mitre saw onto the supporting arm, feeding the
socket head cylinder cap screws through each mounting
hole.
u Use a plain washer and nut (10) to hold in position.
u Repeat the above 4 steps to install second bracket to the
other side of the saw.
u Make sure the brackets are parallel to each other. Use a
tool adjustable wrench to tighten each nut.
Attaching the mitre saw and bracket assembly to
stand (Fig. F & G)
u Lift the saw and bracket assembly, allowing the assembly
to tilt slightly toward your body.
u When the the bracket assembly is tilted toward you, hook
its front edge onto the front rail of the stand, see Figure F.
Warning! To avoid serious injury, before seating the rear
end of the bracket, make sure the curved front edge of the
mounting bracket are securely seated over the front rail .
Failure to do so could cause you to lose control of the saw
mounting assembly.
u Lower the bracket assembly, allowing its rear edge to fully
seat over the rear rail, Figure G.
Note: Use one hand to hold the mounting bracket assembly
until both levers are securely locked.
u Check position and adjust if necessary, to make sure the
weight of the saw is evenly balanced over the rails as
shown in Figure G.
u Ensure the saw is fully seated and locked in position, then
tighten the four nuts to hold the saw to the mounting
bracket.
Removing saw from stand
u Loosen the locking arms to unlock the saw and mounting
bracket assembly.
u Lift the saw away from the rear rail of the stand to
disengage.
u Slightly tilt the assembly toward you, lift the front part of
the assembly to disengage from the front rail of the stand,
see Figure F.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley FME790 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info