Bedienungsanleitung Stanley FMHT1-77414 (Seite 10 von 198) (Alle Sprachen)

720739

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

Plumb Dot Accuracy

Checking the plumb calibration of the laser can be most

accurately done when there is a substantial amount of vertical

height available, ideally 25’ (7.5 m), with one person on the oor

positioning the laser and another person near a ceiling to mark

the dot created by the beam on the ceiling.

Mark point P1 on the oor (Figure

#1).

Turn the laser ON and press once to display dots above

and below the laser.

Place the laser so that the down dot is centered over point

P1 and mark the center of the up dot on the ceiling as point

P2 (Figure

#1).

Turn the laser 180°, making sure that the down dot is still

centered on point P1 on the oor (Figure

#2).

Mark the center of the up dot on the ceiling as point P3

(Figure

#2).

Measure the distance between points P2 and P3.

If your measurement is greater than the Allowable

Distance Between P2 & P3 for the corresponding

Distance Between Ceiling & Floor in the following table,

the laser must be serviced at an authorized service center.

Distance Between

Ceiling & Floor

Allowable Distance

Between P2 & P3

4.5m (15′) 3mm (1/8”)

6m (20′) 4.2mm (5/32”)

9m (30′) 6mm (1/4”)

12m (40′) 8.4mm (5/16”)

Using the Laser

Operating Tips

• Always mark the center of the beam created by the laser.

• Extreme temperature changes may cause movement of

internal parts that can affect accuracy. Check your accuracy

often while working.

• If the laser is ever dropped, check to make sure it is still

calibrated.

• As long as the laser is properly calibrated, the laser is self-

leveling. Each laser is calibrated at the factory to nd level as

long as it is positioned on a at surface within average ± 4°

of level. No manual adjustments are required.

• Use the laser on a smooth, at, level, surface.

Turning the Laser Off

Slide the Power/Transport Lock switch to the OFF/Locked

position (Figure

#1a) when the laser is not in use. If the

switch is not placed in the Locked position, the laser will not

turn off.

Using the Laser with Accessories

WARNING:

Since accessories other than those offered by

Stanley have not been tested with this laser, use of

such accessories with this laser could be hazardous.

Only use Stanley accessories that are recommended for use

with this model. Accessories that may be suitable for one laser

may create a risk of injury when used with another laser.

The bottom of the laser is equipped with 1/4-20 and 5/8-11

female threads (Figure

) to accommodate current or future

Stanley accessories. Only use Stanley accessories specied

for use with this laser. Follow the directions included with the

accessory.

Recommended accessories for use with this laser are available

at extra cost from your local dealer or authorized service center.

If you need assistance locating any accessory, please contact

your nearest Stanley service center or visit our website:

http://www.2helpU.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT1-77414 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info