Bedienungsanleitung Stanley FMHT1-77442 (Seite 8 von 222) (Alle Sprachen)

720742

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

Push the battery compartment cover down until it snaps in

place (Figure

#3).

Slide the Power/Transport Lock switch to the right to the

Unlocked/ON position (Figure

#1b).

On the keypad (Figure

#3b), make sure is green

(> 5%). If is red, this means that the battery level is

below 5%.

• The laser may continue to operate for a short time while

the battery power continues to drain, but the laser lines

and dots will quickly dim.

• After fresh batteries are installed and the laser is turned

ON again, the laser lines and dots will return to full

brightness.

When the laser is not in use, slide the Power/Transport

Lock switch to the LEFT to the Locked/OFF position

(Figure

#1a) to save battery power.

Using the Mounting Block

On the bottom of the laser is a moveable block (Figure

• To use the magnets on the front of the laser (Figure

#2) to

mount the laser against the side of a steel beam, do not

extend the moveable block (Figure

#1). This will allow the

down dot to be aligned with the edge of the steel beam.

• To mount the laser over a point on the oor (using a multi-

function bracket or a tripod), pull out the moveable block until

it clicks in place (Figure

#2). This will allow the laser down

dot to display through the 5/8-11 mounting hole and the laser

to be rotated over the 5/8-11 mounting hole without moving

the vertical position of the laser.

Turning the Laser On

Place the laser on a smooth, flat, level surface.

Slide the Power/Transport Lock switch to the right to the

Unlocked/ON position (Figure

#1b).

As shown in Figure

#3a, press once to display

a horizontal laser line, a second time to display a vertical

laser line, a third time to display a horizontal line and

a vertical line, a fourth time to display 5 dots, and a fifth

time to display the horizontal and vertical lines with the 5

dots.

Check the laser beams. The laser is designed to self-level.

If the laser is tilted so much that it cannot self-level (> 4°),

the laser beams will continually flash twice and will flash

constantly on the keypad (Figure

#3c).

If the laser beams ash, the laser is not level (or plumb)

and should NOT BE USED for determining or marking level

or plumb. Try repositioning the laser on a level surface.

Press on the keypad to test the Pulse mode. will

illuminate on the keypad (Figure

#3d) and the laser

beams will appear lighter, since they are ashing at a very

rapid rate. You will only use Pulse mode with a detector to

project the laser beams long range.

If ANY of the following statements are TRUE, continue with

the instructions for Checking Laser Accuracy BEFORE

USING THE LASER for a project.

• This is the first time you are using the laser (in case

the laser was exposed to extreme temperatures).

• The laser has not been checked for accuracy in

a while.

• The laser may have been dropped.

Checking Laser Accuracy

The laser tools are sealed and calibrated at the factory. It

is recommended that you perform an accuracy check prior

to using the laser for the rst time (in case the laser was

exposed to extreme temperatures) and then regularly to

ensure the accuracy of your work. When performing any of the

accuracy checks listed in this manual, follow these guidelines:

• Use the largest area/distance possible, closest to the

operating distance. The greater the area/distance, the easier

to measure the accuracy of the laser.

• Place the laser on a smooth, at, stable surface that is level

in both directions.

• Mark the center of the laser beam.

Horizontal Line Accuracy - Tilt

Checking the tilt of the laser’s horizontal line requires a at

vertical surface at least 30’ (9m) wide.

Place the laser as shown in Figure

#1 and turn the laser

ON.

Press 3 times to display a horizontal line and a vertical

line.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT1-77442 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info