Bedienungsanleitung Stanley FMHT1-77442 (Seite 9 von 222) (Alle Sprachen)

720742

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

Aim the laser’s vertical line at the rst corner or reference

point (Figure

#1).

Measure half the distance across the wall (D1/2)

(Figure

#1).

Where the horizontal laser line crosses the halfway point

(D1/2), mark point P1 (Figure

#1).

Rotate the laser to another corner or reference point

(Figure

#2).

Where the horizontal laser line crosses the halfway point

(D1/2), mark point P2 (Figure

#2).

Measure the vertical distance between P1 and P2

(Figure

#3).

If your measurement is greater than the Allowable

Distance Between P1 & P2 for the corresponding

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Distance (D1)

Allowable Distance

Between P1 and P2

9 m (30’) 3 mm (1/8”)

12 m (40’) 4 mm (5/32”)

15 m (50’) 5 mm (7/32”)

Horizontal Line Accuracy - Level

Checking the level of the laser’s horizontal line requires a at

vertical surface at least 30’ (9 m) wide.

Place the laser at one end of the wall as shown

in Figure

#1, and turn the laser ON.

Press once to display a horizontal line.

Mark two points (P1 and P2) at least 30’ (9 m) apart along

the length of the laser’s horizontal line on the wall

(Figure

#1).

Relocate the laser at the other end of the wall and align the

laser’s horizontal line with point P2 (Figure

#2).

Mark point P3 on the laser line near point P1

(Figure

#2).

Measure the vertical distance between points P1 and P3

(Figure

#2).

If your measurement is greater than the Allowable

Distance Between P1 & P3 for the corresponding

Distance Between P1 & P2 in the following table, the laser

must be serviced at an authorized service center.

Distance Between

P1 & P2

Allowable Distance

Between P1 and P3

9 m (30’) 6 mm (1/4”)

12 m (40’) 8 mm (5/16”)

15 m (50’) 10 mm (13/32”)

Vertical Line Accuracy - Plumb

Checking the plumb of the laser’s vertical line.

Measure the height of a door jamb (or a reference point on

the ceiling) to get height D1 (Figure

#1).

Place the laser as shown in Figure

#1 and turn the laser

ON.

Press twice to display a vertical line.

Aim the laser’s vertical line toward the door jamb or the

reference point on the ceiling (Figure

#1).

Mark points P1, P2, and P3, as shown in Figure

#1.

Move the laser to the opposite side of point P3 and aim the

laser’s vertical line toward point P2 (Figure

#2).

Align the vertical line with points P2 and P3, and mark point

P4 (Figure

#2).

Measure the distance between P1 and P4 (Figure

#3).

If your measurement is greater than the Allowable

Distance Between P1 & P4 for the corresponding Vertical

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Height of Vertical

Distance (D1)

Allowable Distance

Between P1 and P4

2.5 m (8’) 1.5 mm (1/16")

5 m (16′) 3.0 mm (1/8”)

6 m (20’) 3.6 mm (9/64”)

9 m (30′) 5.5 mm (9/32”)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT1-77442 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info