Bedienungsanleitung Stanley FMHT1-77442 (Seite 11 von 222) (Alle Sprachen)

720742

Zoom out

Zoom in

Vorherige Seite

1/222

Nächste Seite

Using a target to transfer the front level dot location on the

wall to the oor, mark point P2 on the floor and then point

P3 on the floor (Figure

#1).

Move the laser to point P2 and align the front level dot to

point P3 again (Figure

#2).

Using a target to transfer the front level dot location on the

wall to the oor, mark the location of two square beams as

points P4 and P5 on the oor (Figure

#2).

Turn the laser 90° so the front level dot aligns to point P4

(Figure

#3).

Mark the location of the rst square beam as point P6 on

the oor as close as possible to point P1 (Figure

#3).

Measure the distance between points P1 and P6

(Figure

#3).

10.

If your measurement is greater than the Allowable

Distance Between P1 & P6 for the corresponding

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Distance (D1)

Allowable Distance

Between P1 & P6

7.5 m (25’) 2.2 mm (3/32”)

9 m (30’) 2.7 mm (7/64”)

15 m (50’) 4.5 mm (3/16”)

11.

Turn the laser 180° so the front level dot aligns to point P5

(Figure

#4).

12.

Mark the location of the second square beam as point P7

on the oor as close as possible to point P1 (Figure

#4).

13.

Measure the distance between points P1 and P7

(Figure

#4).

14.

If your measurement is greater than the Allowable

Distance Between P1 & P7 for the corresponding

Distance (D1) in the following table, the laser must be

serviced at an authorized service center.

Distance (D1)

Allowable Distance

Between P1 & P7

7.5 m (25’) 2.2 mm (3/32”)

9 m (30’) 2.7 mm (7/64”)

15 m (50’) 4.5 mm (3/16”)

Using the Laser

Operating Tips

• Always mark the center of the beam created by the laser.

• Extreme temperature changes may cause movement of

internal parts that can affect accuracy. Check your accuracy

often while working.

• If the laser is ever dropped, check to make sure it is still

calibrated.

• As long as the laser is properly calibrated, the laser is self-

leveling. Each laser is calibrated at the factory to nd level as

long as it is positioned on a at surface within average ± 4°

of level. No manual adjustments are required.

• Use the laser on a smooth, at, level, surface.

Turning the Laser Off

Slide the Power/Transport Lock switch to the OFF/Locked

position (Figure

#1a) when the laser is not in use. If the

switch is not placed in the Locked position, the laser will not

turn off.

Using the Laser with Accessories

WARNING:

Since accessories other than those offered by

Stanley have not been tested with this laser, use of

such accessories with this laser could be hazardous.

Only use Stanley accessories that are recommended for use

with this model. Accessories that may be suitable for one laser

may create a risk of injury when used with another laser.

The bottom of the laser is equipped with 1/4-20 and 5/8-11

female threads (Figure

) to accommodate current or future

Stanley accessories. Only use Stanley accessories specied

for use with this laser. Follow the directions included with the

accessory.

Recommended accessories for use with this laser are available

at extra cost from your local dealer or authorized service center.

If you need assistance locating any accessory, please contact

your nearest Stanley service center or visit our website:

http://www.2helpU.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMHT1-77442 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info