Bedienungsanleitung Stanley SBD20 (Seite 6 von 26) (Englisch, Französisch)

720436

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENGLISH (Original instructions)

LABELS ON TOOL

The following symbols are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Always wear safety goggles

Always wear safety hearing protection

POSITION OF DATE CODE

The Date Code, which also includes the year of manufacture,

is printed into the housing.

Example:

2017 XX JN

Year of manufacturing

Additional safety instructions for batteries and

chargers

Batteries

• Never attempt to open for any reason.

• Do not expose the battery to water.

• Do not store in locations where the temperature may

exceed 40 °C.

• Charge only at ambient temperatures between 10 °C and

40 °C.

• Charge only using the charger provided with the tool.

• When disposing of batteries, follow the instructions given in

the section "Protecting the environment".

Do not attempt to charge damaged batteries.

Chargers

• Use your Stanley charger only to charge the battery in the

tool with which it was supplied. Other batteries could burst,

causing personal injury and damage.

• Never attempt to charge non-rechargeable batteries.

• Have defective cords replaced immediately.

• Do not expose the charger to water.

• Do not open the charger.

• Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains voltage

corresponds to the voltage on the rating plate. Never

attempt to replace the charger unit with a regular

mains plug.

• If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley Service Centre in

order to avoid a hazard.

FEATURES

This appliance includes some or all of the following features.

1. Trigger Switch

2. Forward/Reverse Button

3. Torque Adjust Collar

4. Dual Range Gear Selector

5. Keyless Chuck

6. Battery

7. Battery Release Button

8. LED Work Light

9. Bit Tip Holder

Use

Warning! Let the tool work at its own pace. Do not overload.

CHARGING THE BATTERY

The battery needs to be charged before ﬁrst use and whenever

it fails to produce sufﬁcient power on jobs that were easily done

before. The battery may become warm while charging; this is

normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tempera-

ture: approx. 24 °C.

Note: The charger will not charge a battery if the cell tempera-

ture is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger will

begin to charge automatically when the cell temperature warms

up or cools down.

• Plug the charger into an appropriate outlet before inserting

the battery pack.

• Insert the battery pack into the charger.

The green LED will ﬂash indicating that the

battery is being charged.

The completion of charge is indicated by the

green LED remaining on continuously.

The pack is fully charged and may be used at

this time or left in the charger.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SBD20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info