Bedienungsanleitung Stanley SBD20 (Seite 8 von 26) (Englisch, Französisch)

720436

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

ENGLISH (Original instructions)

Keyless chuck - ﬁgure F

Warning! Make certain the battery pack is removed to prevent

tool actuation before installing or removing accessories.

To insert a drill bit or other accessory:

• Grasp the chuck (5) and rotate it in the counterclockwise

direction, as viewed from the chuck end.

• Insert the bit or other accessory fully into the chuck, and

tighten securely by rotating the chuck in the clockwise

direction as viewed from the chuck end.

Warning! Do not attempt to tighten or loosen drill bits (or any

other accessory) by gripping the front part of the chuck and

turning the tool on. Damage to the chuck and personal injury

may occur when changing accessories.

Screw driving

• For driving fasteners, the forward/reverse button should be

pushed to the left.

• Use reverse (button pushed to the right) for removing

fasteners.

Note: When moving from forward to reverse, or vice versa,

always release the trigger switch ﬁrst.

Drilling

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the

Safety Instructions.

• Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

• Secure and maintain work area, as instructed in the Safety

Instructions.

• Run the drill very slowly, using light pressure, until the hole

is started enough to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deﬂect the bit.

• Hold the drill ﬁrmly with two hands, one hand on the handle,

and the other gripping the bottom around the battery area

or the auxiliary handle if provided.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL

OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE

TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure

and slowly drilling through the last part of the hole.

• Keep the motor running while pulling the bit out of a drilled

hole. This will help reduce jamming.

• Make sure switch turns drill on and off.

Drilling in wood

Holes in wood can be made with the same twist drill bits used

for metal or with spade bits.

These bits should be sharp and should be pulled out frequently

when drilling to clear chips from the ﬂutes.

Drilling in metal

Use a cutting lubricant when drilling metals. The exceptions are

cast iron and brass which should be drilled dry. The cutting

lubricants that work best are sulphurized cutting oil.

To remove the battery pack from the tool - ﬁgure B

• Press the battery release button (7) and ﬁrmly pull the

battery pack out of the tool handle.

• Insert battery pack into the charger as described in the

charger section of this manual.

USE

Trigger switch & forward/reverse button - ﬁgure C

• The drill is turned ON and OFF by pulling and releasing the

trigger switch (1) shown in ﬁgure C.

The farther the trigger is depressed, the higher the speed of

the drill.

• A forward/reverse control button (2) determines the

rotational direction of the tool and also serves as a lock off

button.

• To select forward rotation, release the trigger switch and

depress the forward/reverse control button on the right side

of the tool.

• To select reverse, depress the forward/reverse control

button on the left side of the tool.

• The center position of the control button locks the tool in the

off position. When changing the position of the control

button, be sure the trigger is released.

USE

Adjusting torque control - ﬁgure D

This tool is ﬁtted with a torque adjustment collar (3) to select the

operating mode and to set the torque for tightening screws.

Large screws and hard workpiece materials require a higher

torque setting than small screws and soft workpiece materials.

• For drilling in wood, metal and plastics, set the collar to the

drilling position symbol.

• For screwdriving, set the collar to the desired setting. If you

do not yet know the appropriate setting, proceed as follows:

• Set the collar to the lowest torque setting.

• Tighten the ﬁrst screw.

• If the clutch ratchets before the desired result is achieved,

increase the collar setting and continue tightening the

screw.

• Repeat until you reach the correct setting.

• Use this setting for the remaining screws.

Dual range switch - ﬁgure E

The dual range feature of your drill allows you to shift gears for

greater versatility.

• To select low speed, high torque setting (position1), turn

tool off and permit to stop. Slide gear shifter button (4)

away from the chuck.

• To select the high speed, low torque setting (position 2),

turn tool off and permit to stop. Slide gear shifter button

back toward the chuck.

Note: Do not change gears when tool is running. If you are

having trouble changing gears, make sure that the dual range

gear button is either completely pushed forward or completely

pushed back.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SBD20 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info