Bedienungsanleitung Stanley SCD12 (Seite 10 von 14) (Englisch, Französisch, Portugiesisch, Türkisch)

720471

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the main handle (i).

Trigger Switch (Fig. A)

To turn the tool on, squeeze the trigger switch (1). To turn the

tool off, release the trigger switch. Your tool is equipped with

a brake. The chuck will stop when the trigger switch is fully

released.

The variable speed switch enables you to select the best speed

for a particular application. The further you squeeze th

e trigger,

the faster the tool will operate. For maximum tool life, use

variable speed only for starting holes or fasteners

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should be

avoided.

Forward/Reverse Control Button

(Fig. A)

A forward/reverse control button (2) determines the direction of

the tool and also serves as a lock-off button.

To select forward rotation, release the trigger switch and depress

the forward/reverse control button on the right side of the tool.

To select revers

e, depress the forward/reverse control button on

the left side of the tool. The center position of the control button

locks the tool in the off position. When changing the position of

the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate a problem.

LED Worklight (Fig. A)

There is a LED worklight (8) located under the torque

adjustment collar (3). The worklight will b

e activated when the

trigger switch is squeezed.

NOTE: The worklight is for lighting the immediate work surface

and is not intended to be used as a flashlight.

Torque Adjustment Collar (Fig. A)

The torque adjustment collar (3) is clearly marked with numbers

and a drill bit symbol.The collar should be rotated until the desired

setting is located at the top of the tool. Locators are provided in the

collar to eliminate the guess work when selecting fastening torque.

The higher the number on the collar, the higher the torque and

the larger the fastener

which can be driven. To lock the clutch for

drilling operations, move to the drill bit position.

NOTE:

When using the drill/driver for drilling holes, be sure that

the torque adjusting collar is set so the figure of the drill is aligned

with the center line on the top ofthe tool. Failure to do this will

allow the clutch to slip while attempting to drill.

Gear Shifter (Fig. A, D)

The dual range feature of your driver/drill allows you to shift gears

for greater versatility.

To select the low speed, high torque setting, turn the tool off and

permit to stop. Slide the gear shifter (4) forward (towards the

chuck). To select the high speed, low torque setting, turn the tool

off and permit to stop. Slide the gear shifter back (away from

chuck).

NOTE:

Do not change gears when the tool is running. If you

are having trouble changing gears, make sure that the dual range

gear shifter is either completely pushed forward or completely

pushed back.

Keyless Chuck (Fig. E)

Your tool features a keyless chuck with one rotating sleeve for

one-hande

d operation of the chuck. To insert a drill bit or other

accessory, follow these steps.

1. Lock the trigger in the OFF position as previously described.

2. Grasp the black sleeve of the chuck with one hand and

use the other hand to secure the tool. Rotate the sleeve

counterclockwise far enough to accept the desired

accessory.

3. Insert the accessory about 19 mm (3/4") into the chuck and

tighten securely by rotating the chuck sleeve clockwise with

one hand while holding the tool with the other. Your tool is

equipped with an automatic spindle lock mechanism. This

allows you to open and close the

chuck with one hand.

To release the accessory, repeat step 2 above.

WARNING:

Do not attempt to tighten drill bits

(or any other accessory) by gripping the front part

of the chuck and turning the tool on. Damage to the

chuck and personal injury may result. Always lock

off trigger switch when changing acces sories.

Be sure to tighten chuck with one hand on the chuck sleeve and

one hand holding the tool for maximum tightness.

Chuck removal (FIG. F)

Turn the adjustment collar to the “drill” position and gear shifter

to position 1 (low speed). Tighten the chuck around the shorter

end of a hex key (not supplied) of 6.35 mm (1/4") or greater

size. Using a wooden mallet or similar object

, strike the longer

end in the clockwise direction, as shown. This will loosen the

screw inside the chuck.

Open chuck jaws fully, insert screwdriver (or Torx tool if required)

into front of chuck between jaws to engage screw head.

Remove screw by turning clockwise (left-hand-thread). Place

hex key in chuck and tighten, as shown in Figure F. Using

a wooden mallet or similar object, strike key sharply in the

counterclockwise direction. This will loosen the chuck so that it

can be unscrewed by hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SCD12 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info