Bedienungsanleitung Stanley SCD12 (Seite 11 von 14) (Englisch, Französisch, Portugiesisch, Türkisch)

720471

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

ENGLISH

Chuck installation (FIG. G)

Screw the chuck on by hand as far as it will go and insert screw

(left-hand thread). Tighten screw securely. Tighten the chuck

around the shorter end of a 6.35 mm (1/4") or larger hex key

(not supplied) strike the longer end in the clockwise direction

with a wooden mallet, as shown. Tighten the screw once again

by turning in a counterclockwise direction.

Drill Operation

WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect

tool from power source before making any

adjustments or removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped firmly. If drilling

thin material, use a wood “back-up” block to

prevent damage to the material.

Turn the collar to the drill bit symbol for drilling. Select the desired

speed/torque range using the gear shifter to match the speed and

torque to the planned operation.

• Use sharp drill bits only. For WOOD, use twist drill bits,

spade bits, or

hole saws. For METAL, use high-speed steel

(HHS) twist drill bits or hole saws.

• Always apply pressure in a straight line with the bit. Use

enough pressure to keep drill biting, but do not push hard

enough to stall the motor or deflect the bit.

• Hold tool firmly with both hands to control the twisting

action of the drill.

WARNING: The drill may stall if overloaded

causing a sudden twist. Always expect the stall.

Grip the drill firmly with both hands to control the

twisting action and avoid injury.

• IF DRILL STALLS, it is usually because it is

being overloaded or improperly used. RELEASE

TRIGGER IMMEDIATELY, remove drill bit from

work, and determine cause of stalling. DO NOT CLICK

TRIGGER ON AND OFF IN AN ATTEMPT

TO START A STALLED DRILL — THIS CAN

DAMAG

E THE DRILL.

• To minimize stalling or breaking through the material,

reduce pressure on drill and ease the bit through the last

fractional part of the hole.

•

Keep the motor running when pulling the bit back out of a

drilled hole. This will help prevent jamming.

•

With variable speed drills there is no need to center punch

the point to be drilled. Use a slow speed to start the hole

and accelerate by squeezing the trigger harder when the

hole is

deep enough to drill without the bit skipping out.

Operation as a Screwdriver

Select the desired speed/torque range using the dual range

gear shifter on the top of tool to match the speed and torque to

the planned operation.

Insert the desired fastener accessory into the chuck as you

would any drill bit. Make a few practice runs in scrap or unseen

areas to determine the proper position of the clutch collar.

MAXIMUM RECOMMENDED CAPACITIES

Low Range–1 High Range–2

Bits, Metal

Drilling

6.00 mm 3.00 mm

Wood, Flat

Boring

19.00 mm 12.00 mm

Hole Saws 19.00 mm 16.00 mm

Maintenance

Your STANLEY power tool has been designed to operate over a

long period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and regular

cleaning.

WARNING: To reduce the risk

of serious personal injury, place

the forward/reverse button in

the lock-off position or turn tool

off and disconnect battery pack

before making any adjustments or

removing/installing attachments or

accessories. An accidental start-up can

cause injury.

The charger and battery pack are not serviceable. There are no

serviceable parts inside.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of the

main housing with dry air as often as dirt is seen

collecting in and around the air vents. Wear

approved eye protection and approved dust mask

when performing this procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SCD12 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info