Bedienungsanleitung Stanley SFMCCS630 (Seite 18 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720477

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

ENGLISH

Regular maintenance ensures a long effective life for your

chainsaw.

Chain and Bar

After every few hours of use, remove the sprocket cover, guide

bar and chain and clean thoroughly using a soft bristle brush.

Ensure oiling hole on bar is clear of debris. When replacing dull

chains with sharp chains it is good practice to flip the chain bar

from bottom totop.

Saw Chain Sharpening (Fig. O–Q)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

NOTE: The cutters will dull immediately if they touch the

ground or a nail whilecutting.

To get the best possible performance from your chain saw it is

important to keep the teeth of the chain sharp. Follow these

helpful tips for proper saw chain sharpening:

1. For best results use a 4.5mm file and a file holder or filing

guide to sharpen your chain. This will ensure you always get

the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth gauge

of thecutter.

3. Figure O- Keep the correct top plate

21

filing angle line

of 30° on your file guide parallel with your chain (file at 60°

from chain viewed from the side).

4. Sharpen cutters on one side of the chain first. File from the

inside of each cutter to the outside. Then turn your saw

around and repeat the processes (2,3,4) for cutters on the

other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion of

chain link in front of the cutter) so they are about 0.635mm

below the tips of the cutters as shown in FigureP.

5. Figure Q- Keep all cutter lengthsequal.

6. If damage is present on the chrome surface of the top plates

or side plates, file back until such damage isremoved.



CAUTION: After filing, the cutter will be sharp, use extra

caution during thisprocess.

NOTE: Each time the chain is sharpened, it loses some of the

low kickback qualities and extra caution should be used. It

is recommended that a chain be sharpened no more than

fourtimes.

Accessories



WARNING: The use of accessories not recommended in

this manual may behazardous.

Replacement chain and bar are available from your nearest

STANLEYFATMAX authorized service center. For use only with

low kick back bar andchain.

Available bars and chains for SFMCCS630:

• Bar: 30cm service part number N727097

• Chain: 30cm service part number N580237

Optional Accessories



WARNING: Since accessories, other than those offered by

STANLEYFATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only STANLEYFATMAX

recommended accessories should be used with

thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Maintenance

Your STANLEYFATMAX power tool has been designed

to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon

proper tool care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Refer to Saw Chain and Guide Bar Oiling (Fig.H)

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCCS630 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info