Bedienungsanleitung Stanley SFMCCS630 (Seite 16 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720477

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

ENGLISH



WARNING: Never use a cross-handed grip (left hand on

the rear handle and right hand on the front handle).



WARNING: Never allow any part of your body to be in line

with the guide bar

4

when operating the chainsaw.

• Never operate while in a tree, in any awkward position

or on a ladder or other unstable surface. You may lose

control of saw causing severeinjury.

• Keep the chain saw running at full speed the entire

time you arecutting.

• Allow the chain to cut for you. Exert only light pressure.

Do not put pressure on chain saw at end ofcut.



WARNING: When not in use always have the chain

brake engaged and batteryremoved.

On / Off Switch (Fig.L)

Always be sure of your footing and grip the chain saw firmly

with both hands with the thumb and fingers encircling

bothhandles.

To turn the unit on, ensure chain brake is not engaged. Slide

the lock off lever

2

, shown in FigureL, and squeeze the trigger

switch

1

. Once the unit is running, you may release the lock

offlever.

In order to keep the unit running you must continue to squeeze

the trigger. To turn the unit off, release thetrigger.

NOTE: If too much force is applied while making a cut the

saw will turn off. To restart saw, you must release the trigger

switch

1

before the saw will restart. Begin your cut again this

time with less force. Allow the saw to cut at its ownpace.



WARNING: Never attempt to lock a switch in the

ONposition.

Setting The Chain Brake (Fig.K)

Your chain saw is equipped with a motor chain braking system

which will stop the chain quickly in case ofkickback.

1. Remove the battery from thetool.

2. To engage the chain brake, push the chain brake / front

hand guard

3

forward until it clicks intoplace.

3. Pull the chain brake / front hand guard

3

towards the front

handle

13

into the “set” position as shown in FigureK.

4. The tool is now ready touse.

NOTE: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop thetool.

Testing The Chain Brake (Fig.A)

Test the chain brake before every use to make sure it

operatescorrectly.

1. Place the tool on a flat, firm surface. Make sure the saw

chain

5

is clear of theground.

2. Grip the tool firmly with both hands and turn the chain

sawon.

3. Rotate your left hand forward around the front handle

13

so the back of your hand comes in contact with the Chain

brake / front hand guard

3

and push it forward, toward the

workpiece. The saw chain should stopimmediately.

NOTE: If saw does not stop immediately, stop use of tool and

bring it to a STANLEYFATMAX service center nearestyou.



WARNING: Make sure to set chain brake beforecutting.

Bubble Level (Fig.A, T)



WARNING: Do not operate above shoulder height Align

bubble levels prior to making acut.

Ideal for horizontal cutting to ensure a straight, flat cut for

fencing, decking or railingposts.

1. Align both bubble levels

7

2. Always start a cut with the saw chain running at fullspeed.

3. Place the bottom spike

22

of the chain saw behind the area

of the initialcut.

4. Once a cut has begun and a notch is established in the

material, do not change the angle of the cut.

NOTE: Changing the angle will cause the bar to bend.

Common Cutting Techniques

(Fig. A, M, N, R, S, T, U)

Felling

The process of cutting down a tree. Be sure battery is fully

charged before felling a tree so you can finish on a single

charge. Do not fell trees in high windconditions.



WARNING: Felling can result in injury. It should only be

performed by a trainedperson.

• A retreat path should be planned and cleared as necessary

before cuts are started. The retreat path should extend

back and diagonally to the rear of the expected line of fall.

(FigureR)

DIRECTION

FALL

RETREAT

45°

TREE

Fig. R

45°

RETREAT

• Before felling is started, consider the natural lean of the

tree, the location of larger branches and the wind direction

to judge which way the tree will fall. Have wedges (wood,

plastic or aluminum) and a heavy mallet handy. Remove

dirt, stones, loose bark, nails, staples, and wire from the tree

where the felling cuts are to bemade.

• Notching Undercut - Make the notch 1/3 of the diameter of

the tree, perpendicular to the direction of the fall. Make the

lower horizontal notching cut first. This will help to avoid

pinching of either the saw chain or the guide bar when the

second notch cut is being made (FigureS).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCCS630 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info