Bedienungsanleitung Stanley SFMCCS630 (Seite 14 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720477

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

ENGLISH

Rear handle

Front handle

Battery

Battery release button

Oil cap

Intended Use

Your STANLEYFATMAX SFMCCS630 Chainsaw is ideal for pruning

applications and cutting logs up to 26cm indiameter.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This chainsaw is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only STANLEYFATMAX battery packs

andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

14

is fullycharged.

To Install the Battery Pack into the Tool

1. Align the battery pack

14

with the rails inside the tool

(Fig.B).

2. Slide it into the tool until the battery pack is firmly seated

and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

15

and firmly pull the battery pack

out of the toolhandle (Fig. B).

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

17

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

ASSEMBLY

Installing the Guide Bar and Saw Chain

(Fig.A, C–E)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

If the saw chain

5

and guide bar

4

are packed separately in the

carton. The chain has to be attached to the bar, and both must

be attached to the body of thetool.

1. Place the saw on a flat, firmsurface.

2. Flip up locking lever and rotate the bar adjust locking

knob

8

counterclockwise as shown in FigureC to remove

sprocket cover

6

3. Wearing protective gloves, grasp the saw chain

5

and wrap

it around the guide bar

4

, ensuring the teeth are facing the

correct direction (see FigureD)

4. Ensure the chain is properly set in the slot around the entire

guidebar.

5. Place the saw chain around the sprocket

18

. While lining up

the slot on the guide bar with chain tensioning pin

20

, and

the bolt

19

, on the base of the tool as shown in FigureE.

6. Once in place, hold the bar still, replace sprocket cover

6

Make sure tool-free tension assembly bolt hole on the

cover lines up with the bolt

19

, in the main housing. Flip

up locking lever and rotate the bar adjust locking knob

8

clockwise until it clicks, then loosen knob one full turn, so

that the saw chain can be properlytensioned.

7. Rotate the chain tensioning knob

9

clockwise to increase

tension as shown in FigureE. Make sure the saw chain

5

snug around the guide bar

4

. Tighten the bar adjust locking

knob until it clicks. The bar is secure after three audible clicks

are heard. Further tightening is notrequired.

Adjusting Chain Tension (Fig. A, F)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

1. With the saw on a flat, firm surface, check the saw chain

5

tension. The tension is correct when the chain snaps back

after being pulled 3mm away from the guide bar

4

with

light force from the index finger and thumb as shown in

FigureF. There should be no “sag” between the guide bar

and the chain on the underside as shown in FigureF.

Stanley SFMCCS630 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info