Bedienungsanleitung Stanley SFMCCS630 (Seite 15 von 196) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720477

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

ENGLISH

2. To adjust saw chain tension, flip up locking tab and rotate

the bar adjust locking knob

8

counterclockwise one full

turn. Rotate the chain tensioning knob

9

clockwise until

the chain tension is correct as instructedabove.

3. Do not over-tension the chain as this will lead to excessive

wear and will reduce the life of the bar andchain.

4. Once chain tension is correct, securely tighten bar adjust

lockingknob.

NOTE: The bar adjust locking knob has a detent tightening

system. The sprocket cover is secure after three audible clicks are

heard. Further tightening is notrequired.

5. When the chain is new, check the tension frequently (after

removing battery) during the first 2 hours of use as a new

chain stretchesslightly.

Replacing the Saw Chain (Fig.A, G)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

1. Flip up locking tab and rotate the bar adjust locking knob

8

counterclockwise to release chaintension.

2. Remove sprocket cover

6

as described in Installing the

Guide Bar and Saw Chainsection.

3. Lift the worn saw chain

5

out of the groove in the guide

bar

4

4. Place the new chain in the slot of the guide bar, making sure

the saw teeth are facing the correct direction by matching

the arrow on the chain with the graphic on the sprocket

cover

6

shown in FigureG.

5. Follow instructions for

Installing the Guide Bar and

SawChain

Replacement chain and bar are available from your nearest

STANLEYFATMAX servicecenter.

• SFMCCS630 requires replacement chain # STZCS230, service

part number N580237. Replacement 30cm bar #STZCS1230,

service part numberN727097.

Saw Chain and Guide Bar Oiling (Fig.H)

Auto Oiling System

This chain saw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated. The

oil level indicator

10

shows the level of the oil in the chain

saw. If the oil level is less than a quarter full, remove the battery

from the chain saw and refill with the correct type of oil. Always

empty oil tank when finishedcutting.

NOTE: Use a high quality bar and chain oil for proper chain

and bar lubrication. As a temporary substitute, a non-detergent

SAE30 weight motor oil can be used. The use of a vegetable

based bar and chain oil is recommended when pruning trees.

Mineral oil is not recommended because it may harm trees.

Never use waste oil or very thick oil. These may damage your

chainsaw.

Filling the Oil Reservoir

1. Flip down locking lever and unscrew counterclockwise

a quarter turn and then remove the oil cap

16

. Fill the

reservoir with the recommended bar and chain oil until the

oil level has reached the top of the oil level indicator

10

2. Refit the oil cap and tighten clockwise a quarter turn. Flip up

locking lever to its lockedposition.

3. Periodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Transporting Saw (Fig.A, I)

1. Always remove the battery from the tool and cover

the guide bar

4

with the scabbard

11

(FigureI) when

transporting thesaw.

2. Engage chain brake by pushing chain brake / front hand

guard

3

forward.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. A, J)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires the left hand on the front

handle

13

, with the right hand on the rear handle

12

Operating the Chain Saw (Fig.A)



WARNING: Read and understand all instructions. Failure

to follow all instructions listed below may result in electric

shock, fire and/or serious personalinjury.

• Guard Against Kickback which can result in severe

injury or death. See Important Safety Instructions

Guard Against Kickback, to avoid the risk

ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart. Divide

your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle

13

and your right hand on the rear

handle

12

so that your body is to the left of the

guidebar.

• Do not hold chain saw by front hand guard/ chain

brake

3

. Keep elbow of left arm locked so that left

arm is straight to withstand akickback.

Stanley SFMCCS630 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info