Bedienungsanleitung Stanley SFMCD711 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720423

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Note: Various trackwall hooks and storage congurations

are available.

Please visit our website www.stanleytools.eu/3 for

further information.

Keyless chuck (Fig. G)

Warning! Make certain the battery pack is removed

to prevent tool actuation before installing or

removing accessories.

To insert a drill bit or other accessory:

● Grasp the chuck (5) and rotate it in the counterclockwise

direction, as viewed from the chuck end.

● Insert the bit or other accessory (13) fully into the chuck,

and tighten securely by rotating the chuck in the clockwise

direction as viewed from the chuck end.

Warning! Do not attempt to tighten or loosen drill bits

(or any other accessory) by gripping the front part of

the chuck and turning the tool on.

Damage to the chuck and personal injury may occur when

changing accessories.

Trigger switch & forward/reverse button (Fig. H)

● The drill is turned ON and OFF by pulling and releasing

the trigger switch (1) shown in gure H. The farther the

trigger is depressed, the higher the speed of the drill.

● A forward/reverse control button (2) determines the

rotational direction of the tool and also serves as a lock

off button.

● To select forward rotation, release the trigger switch and

depress the forward/reverse control button on the right

side of the tool.

● To select reverse, depress the forward/reverse control

button on the left side of the tool.

● The center position of the control button locks the tool in

the off position. When changing the position of the control

button, be sure the trigger is released.

Adjusting torque control (Fig. I)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials

require a higher torque setting than small screws and soft

workpiece materials.

● For drilling in wood, metal and plastics, set the collar (3) to

the drilling position symbol.

● For drilling in light masonry, set the collar (3) to the

hammer drilling position.

● For screwdriving, set the collar to the desired setting.

If you do not yet know the appropriate setting, proceed as

follows:

u Set the collar to the lowest torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw.

u Repeat until you reach the correct setting.

u Use this setting for the remaining screws.

Dual range switch (Fig. J)

The dual range feature of your drill allows you to shift gears

for greater versatility.

● To select low speed, high torque setting (position1), turn

tool off and permit to stop. Slide gear shifter button (4)

away from the chuck.

● To select the high speed, low torque setting (position 2),

turn tool off and permit to stop. Slide gear shifter

button back toward the chuck.

Note: Do not change gears when tool is running. If you are

having trouble changing gears, make sure that the dual range

gear button is either completely pushed forward or completely

pushed back.

Screw driving

● For driving fasteners, the forward/reverse button should

be pushed to the left.

● Use reverse (button pushed to the right) for removing

fasteners.

Note: When moving from forward to reverse, or vice versa,

always release the trigger switch rst.

Drilling

● Use sharp drill bits only.

● Suppor and secure work properly, as instructed in the

Safety Instructions.

● Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

● Secure and maintain work area, as instructed in the Safety

Instructions.

● Run the drill very slowly, using light pressure, until the hole

is started enough to keep the drill bit from slipping out of it.

● Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deect the bit.

● Hold the drill rmly with two hands, one hand on the

handle, and the other gripping the bottom around the

battery area or the auxiliary handle if provided.

● DO NOT CLICK THE TRIGGER OF A STALLED DRILL

OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE

TO THE DRILL CAN RESULT.

● Minimize stalling on breakthrough by reducing pressure

and slowly drilling through the last part of the hole.

● Keep the motor running while pulling the bit out of a drilled

hole. This will help reduce jamming.

● Make sure switch turns drill on and off.

Drilling in wood

Holes in wood can be made with the same twist drill bits used

for metal or with spade bits. These bits should be sharp and

should be pulled out frequently when drilling to clear chips

from the utes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCD711 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info