Bedienungsanleitung Stanley SFMCS701 (Seite 13 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720684

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

(Original instructions)

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Stanley FatMax Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Operating handle

3. Mounting holes

4. Lower Guard

5. Mitre locking knob

6. Mitre latch button

7. Kerf plate

8. Mitre scale

9. Mitre scale indicator

10. Carry grips

11. Fence

12. Bevel lock knob

13. Rails

13a.Velcro strap

14. Dust port

15. Battery pack

16. Work light switch

17. Lock off lever

18. Rail lock screw

19. Clamp mounting hole

20. Lock down pin

Assembly (Fig. A)

Your mitre saw is part assembled in the carton.

uOpen the box and lift the saw out by using the carry grips

(10) in the base of the saw (Fig. A).

u Place the saw on a smooth, at surface such as a work-

bench or strong table.

u Examine Assembly diagram on page 2 of this manual to

become familiar with the saw and its various parts. The

section on adjustments will refer to these terms and you

must know what and where the parts are.

u The mitre locking knob (5) is not assembled for shipping.

Remove the mitre locking knob (5) from the packaging

and screw onto the saw, see gure G and J for position.

u Your saw has a built-in dust port (14) that allows either

the supplied, but not assembled, dust bag (35) or shop

vacuum system to be connected (Fig. N).

Kerf plate (Fig. J)

The kerf plate (7) is mounted to the table by 6 screws. The

kerf plate (7) height is not adjustable.

Note: If the kerf plate (7) is worn, damaged or needs to be

replaced, repairs should be carried out by authorised repair

agents or STANLEY FATMAX service staff.

Lock down pin (Fig. F)

Warning! The lock down pin should be used ONLY when

carrying or storing the saw. NEVER use the lock down pin for

any cutting operation.

Note: To lift, carry and support the mitre saw during transport

use the two carrying handles (10) located on both sides of the

mitre saw base (Fig. A).

To lock the saw head in the down position, push the saw head

down, push the lock down pin (20) in and release the saw

head. This will hold the saw head safely down for transporting

the saw from place to place. To release, press the saw head

down and pull the pin out.

Warning! Always be sure that the tool is switched off and the

battery is removed from the tool before adjusting or checking

the tools function.

Charging a battery (g. B)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before.

The battery may become warm while charging; this is normal

and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the

charger will begin to charge automatically when the cell

temperature warms up or cools down.

Note: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before rst use.

u Plug the charger (21) into an appropriate outlet before

inserting battery pack (15).

u The green charging light (21a) will blink continuously

indicating that the charging process has started.

u The completion of charge will be indicated by the green

charging light (21a) remaining ON continuously. The

battery pack (15) is fully charged and may be removed

and used at this time or left in the charger (21).

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Charger LED Modes

Charging:

Green LED Intermittent

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCS701 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info