Bedienungsanleitung Stanley SFMCS701 (Seite 14 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720684

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

(Original instructions)

Fully Charged:

Green LED Solid

Hot/Cold Pack Delay:

Green LED Intermittent

Red LED Solid

Note: The compatible charger(s) will not charge a faulty

battery pack. The charger will indicate a faulty battery pack by

refusing to light.

Note: This could also mean a problem with a charger. If the

charger indicates a problem, take the charger and battery

pack to be tested at an authorized service centre.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too cold,

it automatically starts a Hot/Cold Pack Delay, the green LED

(21a) will ash intermittently, while the red LED (21b) will

remain on continuously, suspending charging until the battery

has reached an appropriate temperature. The charger then

automatically switches to the pack charging mode. This

feature ensures maximum battery life.

Battery state of charge indicator (Fig. C)

The battery includes a state of charge indicator to quickly

determine the extent of battery life as shown in gure B. By

pressing the state of charge button (15a) you can easily view

the charge remaining in the battery as illustrated in gure C.

Fitting and removing the battery (g. D, E)

u To t the battery (15), line it up with the receptacle on the

tool (22). Slide the battery into the receptacle and push

until the battery snaps into place.

u To remove the battery, push the battery release button

(15b) while at the same time pulling the battery out of the

receptacle as shown in gure E.

Changing or Installing a New Saw Blade (Fig. G,

H, I)

Warning! To reduce the risk of serious personal injury, turn

tool off and remove the battery pack before transporting,

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Removing the Blade

u Remove battery pack (15) from the saw.

u Raise the arm to the upper position and raise the lower

guard (4) as far as possible.

u Loosen, but do not remove the guard bracket front screw

(24) until the bracket (25) can be raised far enough to

access the blade screw (26). Lower guard will remain

raised due to the position of the guard bracket screw.

u Depress the spindle lock button (28) while carefully rotat-

ing the saw blade (29) by hand until the lock engages.

u Keeping the button depressed, use the other hand and the

hex side of the wrench provided to loosen the blade screw

(26). (Turn clockwise, left-hand threads.)

u Remove the blade screw (26) using the hex side of the

wrench provided, the outer clamp washer (30) and blade

(29). The inner clamp washer (31) may be left on the

spindle (32).

Installing a Blade

u Remove battery pack (15) from the saw.

u With the arm raised, the lower guard (4) held open and

the guard bracket (25) raised, place the blade (29) on the

spindle (32) and against the inner blade clamp (31) with

the teeth on the blade pointing in the direction of rotation

as marked on the saw.

u Assemble the outer clamp washer (30) onto the spindle

(32).

u Install the blade screw (26) and, engaging the spindle lock

(28), tighten the screw (26) rmly with wrench provided

(turn counterclockwise, left-hand threads).

u Return the guard bracket (25) to its original full down posi-

tion and rmly tighten the guard bracket screw (24) to hold

bracket in place.

Cut line guidance system

Warning! Do not stare into work light. Serious eye injury could

result.

Note: The battery must be charged and connected to the

mitre saw.

The cut line guidance system can only be turned On or Off by

the work light switch (16).

To cut through an existing pencil line on a piece of wood, turn

on the cut line guidance system using the work light switch

(16) (not with the main trigger), then pull down on the operat-

ing handle (2) to bring the saw blade close to the wood.

The shadow of the blade will appear on the wood. This

shadow line represents the material that the blade will remove

when performing a cut.

To correctly locate your cut to the pencil line, align the pencil

line with the edge of the blade’s shadow. Keep in mind that

you may have to adjust the mitre or bevel angles in order to

match the pencil line exactly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCS701 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info