Bedienungsanleitung Stanley SFMCS701 (Seite 18 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720684

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

(Original instructions)

9 20°

10 18°

The chart assumes that all sides are of equal length. For a

shape that is not shown in the chart, use the following formula:

180º divided by the number of sides equals the mitre (if the

material is cut vertically) or bevel angle (if the material is cut

laying at).

Cutting compound mitres (g. R3)

A compound mitre is a cut made using a mitre angle and a

bevel angle at the same time. This is the type of cut used to

make frames or boxes with slanting sides like the one shown

in gure R3.

Note: If the cutting angle varies from cut to cut, check that

the bevel lock knob and the mitre lock handle are securely

locked. These must be locked after making any changes in

bevel or mitre. The chart at the end of this manual (Table 1)

will assist you in selecting the proper bevel and mitre settings

for common compound mitre cuts. To use the chart, select the

desired angle A (Fig. R3) of your project and locate that angle

on the appropriate arc in the chart. From that point follow the

chart straight down to nd the correct bevel angle and straight

across to nd the correct mitre angle.

Set your saw to the prescribed angles and make a few trial

cuts. Practice tting the cut pieces together until you develop

a feel for this procedure and feel comfortable with it.

Example: To make a 4-sided box with 26º exterior angles

(Angle A, Fig. R3), use the upper right arc. Find 26° on the arc

scale. Follow the horizontal intersecting line to either side to

get mitre angle setting on saw (42°). Likewise, follow the

vertical intersecting line to the top or bottom to get the bevel

angle setting on the saw (18°). Always try cuts on a few scrap

pieces of wood to verify the settings on the saw.

Cutting base moulding (g. S)

Straight 90º cuts:

Position the wood against the fence and hold it in place as

shown in Figure S. Turn on the saw, allow the blade to reach

full speed and lower the arm smoothly through the cut.

Cutting base moulding up to 3.5" (90 mm) high

vertically against the Fence

Position material as shown in Figure S. All cuts should be

made with the back of the moulding against the fence and with

the bottom of the moulding against the table.

Inside Corner Outside Corner

Left Side

Mitre left 45°

Save left side of cut

Mitre right 45°

Save left side of cut

Right Side

Mitre right 45°

Save right side of cut

Mitre left 45°

Save right side of cut

Material up to 3.5" (90 mm) can be cut as described above.

Cutting crown moulding

In order to t properly, crown moulding must be compound

mitred with extreme accuracy.

The two at surfaces on a given piece of crown moulding are

at angles that, when added together, equal exactly 90°. Most,

but not all, crown moulding has a top rear angle (the section

that ts at against the ceiling) of 52° and a bottom rear angle

(the part that ts at against the wall) of 38°.

Your mitre saw has special preset mitre detent points at 31.6°

left and right for cutting crown moulding at the proper angle.

There is also a mark on the bevel scale at 33.8°.

The Bevel Setting/Type of Cut chart gives the proper settings

for cutting crown moulding. (The numbers for the mitre and

bevel settings are very precise and are not easy to accurately

set on your saw.) Since most rooms do not have angles of

precisely 90°, you will have to ne tune your settings anyway.

Instructions for cutting crown moulding laying at

and using the compound features

u Lay the moulding with broad back surface down at on

saw table (36) (g. T1).

u The settings below are for all Standard crown moulding

with 52° and 38° angles.

Bevel Setting Type Of Cut

33.8°

LEFT SIDE, INSIDE CORNER:

1. Top of moulding against fence

2. Mitre table set right 31.62°

3. Save left end of cut

33.8°

RIGHT SIDE, INSIDE CORNER:

1. Bottom of moulding against fence

2. Mitre table set left 31.62°

3. Save left end of cut

33.8°

LEFT SIDE, OUTSIDE CORNER:

1. Bottom of moulding against fence

2. Mitre table set left 31.62°

3. Save right end of cut

33.8°

RIGHT SIDE, OUTSIDE CORNER:

1. Top of moulding against fence

2. Mitre table set right 31.62°

3. Save right end of cut

Note: When setting bevel and mitre angles for all compound

mitres, remember that the angles presented for crown

mouldings are very precise and difcult to set exactly. Since

they can easily shift slightly and very few rooms have exactly

square corners, all settings should be tested on scrap

moulding.

Alternative method for cutting crown moulding

Place the moulding at an angle between the fence (11) and

the saw table (36), with the top side of the moulding on the

table and the bottom side of the moulding on the fence as

shown in gure T1.

The advantage to cutting crown moulding using this method is

that no bevel cut is required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCS701 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info