Bedienungsanleitung Stanley SFMCS701 (Seite 19 von 184) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

720684

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

(Original instructions)

Minute changes in the mitre angle can be made without af-

fecting the bevel angle. This way, when corners other than 90º

are encountered, the saw can be quickly and easily adjusted

for them.

Instructions for cutting crown moulding angled

between the fence and base of the saw for all cuts

This saw can cut up to 9/16" (14 mm) x 3-5/8" (92 mm) crown

moulding nested.

u Angle the moulding so the bottom of the moulding (part

which goes against the wall when installed) is against the

fence (11) and the top of the moulding is resting on the

saw table (36), as shown in gure T2.

u The angled “ats” on the back of the moulding must rest

squarely on the fence and saw table (36).

Inside Corner Outside Corner

Left Side

Mitre right at 45°

Save right side of cut

Mitre left at 45°

Save right side of cut

Right Side

Mitre left at 45°

Save left side of cut

Mitre right at 45°

Save left side of cut

Special Cuts

Never make any cut unless the material is secured on the

table and against the fence.

Bowed material (g. U1, U2)

When cutting bowed material always position it as shown in

gure U1 and never like that shown in gure U2. Positioning

the material incorrectly will cause it to pinch the blade near

the completion of the cut.

Cutting round material

Rounded material should be clamped or held rmly to the

fence to keep It from rolling. This is extremely important when

making angle cuts.

Cutting large material (g. V)

Occasionally you will encounter a piece of wood a little too

large to t beneath the lower guard. To clear the guard over

the wood, with the saw off and your right hand on the operat-

ing handle, place your right thumb outside of the upper portion

of the guard and roll the guard up just enough to clear the

wood, as shown in gure V. Release the guard prior to starting

the motor. The guard mechanism will function properly during

the cut. Only do this when necessary.

NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD

OPEN WHEN OPERATING THIS SAW.

Maintenance

Warning! To reduce the risk of serious personal injury, turn

tool off and remove the battery pack before transporting,

making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Warning! To reduce the risk of serious personal injury, DO

NOT touch the sharp points on the blade with ngers or hands

while performing any maintenance.

DO NOT use lubricants or cleaners (particularly spray or

aerosol) in the vicinity of the plastic guard. The polycarbon-

ate material used in the guard is subject to attack by certain

chemicals.

u All bearings are sealed. They are lubricated for life and

need no further maintenance.

u Periodically clean all dust and wood chips from around

AND UNDER the base and the rotary table. Even though

slots are provided to allow debris to pass through, some

dust will accumulate.

u The brushes are designed to give you several years of

use. If they ever need replacement, return the tool to the

nearest service centre for repair.

Troubleshooting

Problem Possible Cause Solution

Saw will not

start.

Battery not installed.

Install battery. Refer to Installing

and Removing Battery Pack.

Battery not charged.

Charge battery. Refer to Charging

Procedure.

Brushes worn out

Have brushes replaced by

authorised service centre.

Saw makes

unsatisfactory

cuts.

Dull blade.

Replace blade. Refer to Changing

or Installing a New Saw Blade.

Blade mounted

backwards.

Turn blade around. Refer to

Changing or Installing a New Saw

Blade.

Gum or pitch on

blade.

Remove blade and clean with

coarse steel wool and turpentine or

household oven cleaner.

Incorrect blade for

work being done.

Change the blade type.

Work light is

ashing.

Battery not charged

Charge battery. Refer to Charging

Procedure.

Machine

vibrates

excessively.

Saw not mounted

securely to stand or

work bench.

Tighten all mounting hardware.

Refer to Bench Mounting

Stand or bench on

uneven oor.

Reposition on at level surface.

Damaged saw

blade.

Replace blade. Refer to Changing

or Installing a New Saw Blade.

Does not

make accurate

mitre cuts.

Mitre scale not

adjusted correctly.

Check and adjust. Refer to Mitre

Scale Adjustment under

Adjustments.

Blade is not square

to fence.

Check and adjust. Refer to Mitre

Scale Adjustment under

Adjustments.

Blade is not

perpendicular to

table.

Check and adjust fence. Refer to

Bevel Square to Table Adjustment

under Adjustments.

Work piece moving

Clamp work piece securely to fence

or glue 120 grit sandpaper to fence

with rubber cement.

Kerf plate worn or

damaged.

Take to authorised service centre.

Material

pinches blade.

Cutting bowed

material.

Refer to Bowed Material under

Special Cuts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCS701 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info