Bedienungsanleitung Stanley SFMCST933 (Seite 15 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720561

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

ENGLISH

6. Press the spool down GENTLY and rotate it until you feel it

drop into place and then push to snap into place. (When in

place, the spool will turn a few degrees left and right freely).

7. Take care to keep the line from becoming trapped under

thespool.

8. Fit the spool onto the appliance as described in Replacing

SpoolAssembly.

Replacing Spool Assembly (Fig.K, L)



WARNING: The use of any accessory not

recommended by STANLEYFATMAX for use with this

appliance could behazardous.



WARNING: Do not use any blades, or any

accessory or attachment other than those recommended

by STANLEYFATMAX on this trimmer. Serious injury or

product damage mayresult.

Reload nylon line (either bulk or prewound replacement spool)

as shown in thismanual.

USE ONLY 1.65 mm DIAMETER ROUND NYLON MONOFILAMENT

LINE. Do not use serrated or heavier gauge line, as they will

overload the motor and cause overheating. This line is available

at your local dealer or authorized servicecenter.

1. Remove battery fromappliance.

2. Press the release tabs

19

on the spool cap

18

, and remove

the spool cap from the spool housing

10

(Figure K).

3. For best results, replace spool and line with

STANLEYFATMAX Model # STZST12169/STZST121693

or replace cap only with STANLEYFATMAX

Model#STZST1326.

4. If lever in base of housing becomes dislodged, replace in

correct position before inserting new spool intohousing.

5. Remove any dirt and grass from the spool cap and

spool housing.

6. Unfasten the end of the cutting line and guide the line into

the eyelet.

7. Take the new spool and push it onto the boss

20

in the

housing. Rotate the spool slightly until it isseated.

8. The line should protrude approximately 5-136mm from

thehousing.

9. Align the release tabs on the spool cap with the slots in the

spoolhousing.

10. Snap the spool cap back on by depressing release tabs and

pressing into spoolhousing.

11. Push the cap onto the housing until it snaps securely

intoplace.

NOTE: Make sure that cover is fully positioned, listen for two

audible clicks to ensure both release tabs are correctly located.

Power the appliance on. In a few seconds or less you’ll hear the

nylon line being cut automatically to the properlength.

NOTE: Other replacement parts (guards, spool caps, etc.) are

available through authorized service centers.

Rewinding Spool from Bulk Line (use only

1.65 mm ROUND diameter line) (Fig.A, M, N)

Bulk line is also available for purchase from your local retailer.

NOTE: Hand wound spools from bulk line are likely to become

tangled more frequently than STANLEYFATMAX factory wound

spools. For best results, factory wound spools arerecommended.

1. Remove battery fromappliance.

2. Remove the empty spool from the appliance as described in

Replacing SpoolAssembly.

3. Remove any remaining cutting line from the spool

21

4. Make a fold at the end of the cutting line at about 19

mm. Feed the cutting line into one of the line anchoring

slots

22

.

5. Insert the 19 mm end of the bulk line into the hole

23

the spool adjacent to the slot. Make sure the line is pulled

tight against thespool.

6. Wind the cutting line onto the spool in the direction of the

arrow on the spool. Make sure to wind the line on neatly

and in layers. Do notcrisscross.

7. When the wound cutting line reaches the recesses

24

cut

theline.

8. Fit the spool onto the appliance as described in Replacing

SpoolAssembly.

MAINTENANCE

Your STANLEYFATMAX power tool has been designed

to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon

proper tool care and regularcleaning.



WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect battery

pack before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the

main housing with dry air as often as dirt is seen collecting

in and around the air vents. Wear approved eye protection

and approved dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of the

tool. These chemicals may weaken the materials used in

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCST933 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info