Bedienungsanleitung Stanley SFMCV002 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

722516

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

(Original instructions)

Dry vacuum cleaning

To empty tank (FIG. F)

The sound of the motor changes and suction is reduced when

the tank is full.

u Turn vacuum off. Remove the battery pack.

u Unlatch tank latches (5) and remove power head from

the tank.

u Empty contents of tank into suitable container.

u Clean or change lter (18). See Filter section of this

manual.

u Inspect vacuum for damage by foreign objects.

Contact the nearest Stanley Fat Max authorized service

center for replacement of damaged or missing parts.

u Replace power head (3) onto the tank (4) and latch

securely.

Wet vacuum cleaning

Warning! Do not tilt vacuum when in use.

If vacuum has liquid in the tank it may spill out from the

exhaust port.

Warning! Ensure battery port and terminals are dry and clean

before installing battery pack.

The lter must be removed before using the vacuum to

clean liquids. See Filter section of this manual.

To empty tank

The sound of the motor changes and suction is reduced

when the tank is full.

u Turn vacuum off. Remove the battery pack.

u Unlatch tank latches (5) and remove power head from

the tank.

u Empty contents of tank.

u Inspect vacuum for damage by foreign objects. Contact

the nearest Stanley Fat Max authorized service center for

replacement of damaged or missing parts.

u Dry inside of power head and tank with a clean cloth.

u Replace power head (3) onto the tank (4) and latch

securely.

Filter

Filter care

The wet/dry filter (18) included with this vacuum is a long

life filter. To be effective in minimizing dust recirculation the

filters MUST be installed correctly and in good condition.

Note: A clean filter is the most important factor in the

operation and efficiency of any vacuum. If the filter becomes

clogged beyond cleaning, damaged, or fails to operate

properly, replace only with a reccomended replacement.

To clean or change the filter (Fig. G)

u Turn vacuum off. Remove the battery pack.

u Unlatch the tank latches (5) and remove the power

head from the tank as shown in gure D.

Unlock the lter lock (19) by twisting it counter clockwise.

Pull the lter (18) out to remove it from the power head.

u Clean the lter by shaking off excess dust, tapping into

a waste receptacle, then rinsing under running water.

Depending on the condition of the lter, a water wash is

not always required. Do not use a brush to clean lter.

u Reinstall lter and secure the lter lock onto power

head. Twist the lter lock clockwise and ensure the lter

is locked in place.

u Replace power head onto the tank and secure latches.

Note: Please contact your local service center or visit our

website www.stanley.eu/3 to purchase a filter.

Blower

The blower function can be used to remove debris from

behind small spaces, to dry a damp oor, to blow grass

clippings or leaves from an outside walk, patio, etc.

To use as a blower (Fig. H)

u Empty the tank following the instructions under the

Vacuum Cleaning section of this manual.

u Twist the vacuum hose (8) counter clockwise to remove

from the intake port.

u Align the hose end (16) with the side exhaust port (10),

ensuring the hose alignment lock (15) is aligned with the

arrow (20) above the side exhuast port.

u Insert the hose end into the side exhaust port and twist

clockwise to lock in place.

Hose and accessory storage

When the vacuum is not in use, remove the battery pack.

The vacuum hose can be wrapped around appliance,

underneath the battery interface, and secured with the

hose clip (7) also located at the back of the vacuum. The two

accessories (crevice tool and wide nozzle) can be stored on

board the vacuum as well.

Troubleshooting guide

Problem Possible cause Possible Solution

Unit will

not start Battery pack not

installed properly.

Battery pack not

charged.

Internal compo-

nents too hot.

Brushes worn

out.

Check battery pack installation.

Check battery pack charging require-

ments.

Allow tool to cool down.Have motor

replaced by an authorized Stanley Fat

Max service center.

Have brushes replaced by an authorized

Stanley Fat Max

service center.

Battery

pack

will not

charge.

Battery pack

not inserted into

charger.

Charger not

plugged in.

Surrounding air

temperature too

hot or too cold.

Insert battery pack into

charger until LED illuminates.

Plug charger into a working outlet. Refer

to “Important charging notes” for more

details.

Move charger and battery pack to a

surrounding air temperature below 10 °C

or above 40 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SFMCV002 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info