Bedienungsanleitung Stanley SGM146 (Seite 6 von 28) (Englisch, Französisch)

720762

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

ENGLISH (Original instructions)

l. Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your

control.

m. Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

n. Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical

hazards.

o. Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

p. Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Causes and Operator Prevention of Kickback

Kickback is a sudden reaction to a pinched or snagged

rotating wheel or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of

the binding.

For example, if an abrasive wheel is snagged or pinched by

the workpiece, the edge of the wheel that is entering into the

pinch point can dig into the surface of the material causing the

wheel to climb out or kick out. The wheel may either jump

toward or away from the operator, depending on direction of

the wheel’s movement at the point of pinching. Abrasive

wheels may also break under these conditions.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a. Maintain a ﬁrm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start up. The operator can control torque reaction

or kickback forces, if proper precautions are taken.

b. Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c. Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point of snagging.

d. Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control or

kickback.

e. Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss of control.

Safety Warnings Speciﬁc for Grinding

a. Use only wheel types that are recommended for your

power tool and the speciﬁc guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

b. The grinding surface of the centre depressed wheels

must be mounted below the plane of the guard lip. An

improperly mounted wheel that projects through the plane

of the guard lip cannot be adequately protected.

c. The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator. The

guard helps to protect the operator from broken wheel

fragments, accidental contact with wheel and sparks that

could ignite clothing.

d. Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut-off wheel. Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to these wheels

may cause them to shatter.

e. Always use undamaged wheel ﬂanges that are of

correct size and shape for your selected wheel. Proper

wheel ﬂanges support the wheel thus reducing the

possibility of wheel breakage. Flanges for cut-off wheels

may be different from grinding wheel ﬂanges.

f. Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and may burst.

Additional Safety Information

• This tool is not designed to be used with wire wheels and

wire cup.

WARNING: We recommend the use of a residual

current device with a residual current rating of

30mA or less.

RESIDUAL RISKS

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These are:

_ Impairment of hearing

– Risk of personal injury due ﬂying particles.

– Risk of burns due to accessories becoming hot during

operation.

– Risk of personal injury due to prolonged use.

– Risk of dust from hazardous substances.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SGM146 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info