Bedienungsanleitung Stanley SHR263K (Seite 5 von 24) (Englisch, Französisch)

720442

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH (Original Instructions)

♦ Check for damage to the tool, parts or accessories

which may have occurred during transport.

♦ Take the time to thoroughly read and understand this

manual prior to operation.

ELECTRICAL SAFETY

Your tool is double insulated; therefore no earth wire

is required. Be sure to check that the power supply

corresponds to the voltage on the rating plate.

If the supply cord is damaged, it must be replaced

by the manufacturer or an authorised STANLEY

Service Centre in order to avoid a hazard.

USING AN EXTENSION CABLE

If it is necessary to use an extension cable, please used

an approved extension cable that fits the tool’s power input

specifications. The minimum cross-sectional area of the

conducting wire is 1.5 sq. mm. Cables should be untangled

before reeling up.

Cable cross-sectional

area (mm

)

Cable rated current

(Ampere)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rated current (Ampere)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

FEATURES (FIG. A, FIG.B, FIG. C, FIG. D)

This tool includes some or all of the following features.

1. Main handle

2. Lock-on button

3. Variable speed switch

4. Forward/Reverse lever

5. Mode selector switch

6. Sleeve

7. Tool clamp

8. Depth Stop

9. Side handle

10. Date code

11. SDS Plus bit

12. Drill chuck

13. Drill bit

14. Dust collector

ASSEMBLY

WARNING! Before assembly, make sure that the tool is

switched off and unplugged.

Attaching the Side Handle (FIG. A)

WARNING! When using the tool, please use the side

handle (9) for your safety.

The side handle can be fitted to suit both right-handed and

left-handled users.

♦ Turn the grip counter-clockwise until you can slide the

side handle onto the front of the tool.

♦ Rotate the side handle into the desired position.

♦ Tighten the side handle by turning the grip clockwise.

WARNING! When using the tool, remember to install the

side handles properly.

Fitting an accessory (FIG. A)

♦ Clean and grease the shank (11) of the SDS Plus bit.

♦ Insert the accessory bar into the tool clamp (7).

♦ Push the accessory down and turn it slightly until it ﬁts

into the slots.

♦ Pull on the accessory to check if it is properly locked. The

hammering and drilling function requires the accessory

to be able to move axially several centimetres when

locked in the tool clamp.

♦ To remove the accessory, pull back the sleeve (6) and

pull out the accessory from the tool clamp.

Fitting dust collector (Fig. F)

♦ Insert the SDS Plus bit (11) into dust collector (14), then

insert the bit (11) with dust collector into tool clamp (7).

♦ Use the dust collector only when the unit is used for

upright drilling (Fig. F).

USE

WARNING! Always wear gloves when you change

accessories. The exposed metal parts on the tool and

accessory may become extremely hot during operation.

Please operate tool with normal load. Do not overload. Do

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SHR263K Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info