Bedienungsanleitung Stanley SHR263K (Seite 6 von 24) (Englisch, Französisch)

720442

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

ENGLISH (Original Instructions)

not abuse the tool, please refer instruction manual to use

the tool correctly.

WARNING! Before drilling into walls, ﬂoors or ceilings,

check for the location of wiring and pipes.

Setting the drilling depth (FIG. A)

The depth stop is a convenient feature to ensure uniformity

in drilling depth. Loosen the side handle to adjust the depth

gauge according to the required depth. After that, tighten

the side handle.

♦ Slacken the side handle (9) by turning the grip

counter-clockwise.

♦ Set the depth stop (8) to the required position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

♦ Tighten the side handle by turning the grip clockwise.

Switching on and off (FIG. A)

WARNING! Before plugging in to the power source, make

sure the variable speed switch can be flipped freely, and

can return to its original position once released. Please

check switch lock on position before turn on and make sure

switch lock off before plugging in to the power source.

♦ To switch the tool on, press the variable speed switch (3).

The tool speed depends on how far you press the switch.

♦ As a general rule, use low speeds for large diameter

drill bits and high speeds for smaller diameter drill bits.

♦ For continuous operation, press the lock-on button (2)

and release the variable speed switch.

♦ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Fitting drill chuck (FIG. D)

Optional accessory (not included in the packaging)

♦ Insert the drill chuck suitable for SDS-Plus fitment (12)

into the tool clamp (7) according to the instructions for

installing attachments.

♦ Turn the drill chuck to loosen the clamps at the front-

end of the drill-clamp, and insert the drill bit (13) into

the clamps and turn the chuck in the opposite direction.

♦ You may also use the drill chuck key to tighten the clamp.

Warning: Never use standard chucks in the

hammer-drilling mode

Selecting the Operating Mode (FIG. B)

The tool can be used in the following operating modes:

Rotary drilling: for screw driving and for drilling

into steel, wood and plastics

Hammer drilling: for concrete and masonry

drilling operations. Bit rotation: non-working

position used only to rotate a ﬂat chisel into the

desired position

Hammering only: for light chipping and chiselling.

In this mode the tool can also be used as a lever to

free a jammed drill bit.

1. To select the operating mode, press the mode selector

button and rotate the mode selector switch (5) until it

points to the symbol of the required mode.

2. Release the mode selector button and check that the

mode selector switch is locked in place.

WARNING! Do not select the operating mode when

the tool is running.

Proper Hand Position (FIG. A, FIG. E)

WARNING! To reduce the risk of serious personal

injury, ALWAYS use proper hand position as shown.

WARNING! To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

sudden reaction.

Proper hand position requires one hand on the side handle

(9), with the other hand on the main handle (1).

Rotary drilling (FIG. B, FIG. D, FIG. C1/C2)

♦ For drilling in steel, wood and plastics, or for screw

driving set the operating mode selector (5) to the

position.

♦ Fit the drill chuck assembly by referring to fitting drill

chuck part in this manual.

♦ Insert the appropriate bits. When driving slotted head

screws always use bits with a finder sleeve.

♦ For drilling in steel, wood and plastics, set the forward/

reverse lever(4) to the forward position(Fig C1). When

use for screw driver function, tighten screws set the

forward/reverse lever (4) to the forward position(Fig C1)

and loose screws set the forward/reverse lever (4) to

the reverse position(Fig C2).

WARNING! Never use drill chucks in the hammer drilling

mode.

Hammer drilling (FIG. B)

♦ For hammer drilling in masonry and concrete, set the

operating mode selector (5) to the position.

♦ The drill bit has to be placed accurately onto the drill

hole position. After that, pull the switch for optimal

effects. Make sure the tool is in the correct position to

prevent the drill from deviating from the hole.

♦ When the drill hole is clogged with debris or fine powder,

please don’t exert any more pressure. Tool should be

put in free-running state before removing part of the drill

bit from the hole. If repeated a few times, the blockage

in the hole would be cleared, and normal drilling can

resume.

WARNING! When the drill bit hits the steel rebar in the

cement, the tool may recoil dangerously. Please hold the

tool tightly in a balanced and stable position at all times to

prevent it from recoiling dangerously.

Safety Clutch

All rotary hammer are equipped with a safety clutch that

reduces the maximum torque reaction transmitted to the

operator in case of jamming of a drill bit. This feature also

prevents the gearing and electric motor from stalling. The

torque limiting clutch has been factory-set and cannot be

adjusted.

Chipping and chiselling (FIG. B)

♦ Set the mode selector switch (5) to the“hammering only”

position.

Stanley SHR263K Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info