Bedienungsanleitung Stanley SLM-139-460-SP (Seite 13 von 93) (Deutsch, Englisch, Dänisch, Italienisch, Portugiesisch, Schwedisch, Norwegisch, Finnisch)

720573

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

Maintaining the Spark Plug

A worn spark plug or a spark gap that is too large will

result in a reduction of engine performance.

1. Disconnect the spark plug connector (12) from the

spark plug by simultaneously pulling and turning.

2. Unscrew the spark plug anticlockwise using the spark

plug socket.

3. Check the spark gap using a feeler gauge (available

from specialist shops). The spark gap must be at least 0.7

mm.

4. Clean the spark plug with a wire brush.

5. Insert the cleaned and adjusted spark plug or replace

a damaged spark plug with a new one

Changing the Engine Oil

To change the engine oil, tip the equipment

on a inclined surface .

• Change the engine oil for the ﬁrst time after around

5 operating hours then every 50 operating hours or

annually.

• Change the engine oil when the engine is warm.

• Dispose of the used oil in an ecofriendly manner

1. Open the oil drain plug (8)

2. Drain the engine oil into a suitable container.

3. Wipe up spilt engine oil and screw back in the oil

drain plug (8).

4. Stand the equipment level and reﬁll the engine oil

Sharpening / Changing the Blades

• Always have a blunt blade resharpened by a specialist

workshop, as an imbalance check can be carried out

there.

• Always have a specialist workshop change a damaged

or imbalanced blade. Incorrect installation can result in

serious injury.

Adjusting the Carburettor

The carburettor has been preset in the factory for

- Remove the grass collection box ( 20) if it is installed.

- Adjust the cutting height to position 8

- Set the upper handle bar (2) to around 5° in the

direction of the equipment.

Do not squash the Bowden cables (4) when doing this.

Risk of injury if the equipment tips back.

• Always keep the equipment clean. To

clean, use a toothbrush or cloth but no

corrosive cleaning agents or solvents.

Do not use water to clean the engine as

it could contaminate the fuel system.

• After mowing, remove plant remains

that are stuck to the equipment by using a piece of wood

or plastic. Clean the vent holes, ejection hole and blade

area especially. Do not use hard

or pointed objects, which could damage

the equipment.

• Oil the wheels from time to time.

• Before each use, check the lawnmower for obvious

defects such as loose, worn or damaged parts. Check

that all nuts bolts and screws are sitting ﬁrmly.

• Check covers and guards for damage

and that they are sitting correctly. Replace

if necessary.

Replacing the Air Filter

Do not operate the equipment without the air ﬁlter

otherwise dust and dirt will get into the engine and

result in damage to the machine.

1. Loosen the screw on the air ﬁlter cover (15) and ﬂip

open the cover.

2. Remove the air ﬁlter (14).

3. Replace the air ﬁlter with a new ﬁlter.

4. To install, insert the new air ﬁlter (14) in the air ﬁlter

cover (15).

5. Flip the air ﬁlter cover closed and screw it back

together.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley SLM-139-460-SP Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info